Search:

Type: Posts; User: Stez

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    56
    Views
    2,902

    does Ngauge will work for JTEC - RAM SRT10 2004?

    does Ngauge will work for JTEC - RAM SRT10 2004?
  2. Replies
    0
    Views
    139

    Q50 DTC and Speed Limiter OFF?

    I tuned Q50 via HPT, all seems to work ok, except - Engine Diagnostic is not active - there is nothing in there, the same thing for Speedo , why?
  3. Replies
    1
    Views
    271

    How to raise Desired BT on Ecoboost PTE6262?

    Please see the log file, im trying to get more power of the car, but it closes the TB , i'd assume because of Desired BT is too low, i've tryed to raise Demand Tq and Torques Calc model in that area...
  4. Replies
    0
    Views
    114

    Low load TB not opens

    The car is Mustang 2013" with Edelbrock SC attached, it runs just fine under heavy loads, but have very strange issue with very light loads, sometimes if i press the pedal very slow up to 15-20% , TB...
  5. 6R80 wont shift after ProCharger install, need help

    Please help, we installed Supercharger kit on Mustang 3.7L 2012" , calibrated engine data - it works good on one gear , + 100hp added.
    When cruising on the street everything wokr good untill Full...
  6. Replies
    64
    Views
    16,309

    Sticky: Please advise, i have both MPVI1 and MPVI2 now......

    Please advise, i have both MPVI1 and MPVI2 now... The question is - if i can use my MPVI2 to tune some of the cars which been tuned by MPVI1 long time ago?
  7. Replies
    2
    Views
    230

    any help ???

    any help ???
  8. Replies
    2
    Views
    230

    Cant read any Data for E67 PCM

    Please help, im using VCM Scanner - connecting to E67 gm performance pcm (Please see attached PCM Rom read and cable info) - it makes the connections but can not ready ANY OBD Data, it do not see...
  9. Thread: Cant read ecu (((

    by Stez
    Replies
    10
    Views
    406

    I dont know what more info can i post here...

    I dont know what more info can i post here...
  10. Thread: Cant read ecu (((

    by Stez
    Replies
    10
    Views
    406

    Furthermore, when i connected it to VCM Scanner -...

    Furthermore, when i connected it to VCM Scanner - scanner could not read ANY parameter.... only DTC read was available...
  11. Thread: Cant read ecu (((

    by Stez
    Replies
    10
    Views
    406

    I did, Editor says impossible to find protocol to...

    I did, Editor says impossible to find protocol to make read
  12. Thread: Cant read ecu (((

    by Stez
    Replies
    10
    Views
    406

    Could you please check, we have this ECM...

    Could you please check, we have this ECM
    https://i.gyazo.com/662e829c0fc3ff2730210feef08c5bd6.png
  13. Replies
    5
    Views
    586

    So it can not be read by HPTuners? most tuned ecu...

    So it can not be read by HPTuners? most tuned ecu by third party are easily readable by HPTuners ))))
  14. Thread: Cant read ecu (((

    by Stez
    Replies
    10
    Views
    406

    So if i can not ready it - HPT dont support this...

    So if i can not ready it - HPT dont support this ecm?
  15. Replies
    5
    Views
    586

    Ecoboost 2017 Read issue

    Tryed to read Mustang Ecoboost via MPVI 2 and getting Read Failed - Controller Unlocker: x7F Service Not supported in Active Session

    https://i.gyazo.com/2df5e516c2261dc3b4f1047e3fa39ee1.png
    ...
  16. Thread: Cant read ecu (((

    by Stez
    Replies
    10
    Views
    406

    Cant read ecu (((

    Please advise if it possible to read/wright/log/tune this ECU from the LSA Engine Controller Kit - for individual engine controller, use P/N 19259294 (included in kit)...
  17. Replies
    11
    Views
    1,486

    MPVI2 Pro Feature any ETA date?

    Hello, sorry, if anybody have any ETA date when MPVI Pro will be available?
  18. Replies
    1
    Views
    423

    VCM Scanner 4.1.257 Beta issue!

    Hello, i installed the last software of VCM suite, and the MPVI do not read most parameters, i checked on the few cards Mustang 07" and Cadillac 07" - it read just a few general parameters and speed...
  19. Challenger 2010 SRT8 with Supercharger - Low timing problem

    Please help, we cant understand what is lowering our timing to so low numbers, i guess we missed something like limiter or etc in the software (see tune file and log attached) - any help please...
  20. Sticky: Today, i had Gen 3 on my dyno to make baseline...

    Today, i had Gen 3 on my dyno to make baseline before any tuning... i tryed to make read, VCMsuite does recognized Viper 2006 SRT10... etc.. i choosed JTEC+ for ECU and it does read it well, but VCM...
  21. Sticky: anybody here???

    anybody here???
  22. Sticky: Had read whole thread but still didnt understood...

    Had read whole thread but still didnt understood - if HPT now can read/wright Viper Gen3 ? or still not and will need to use SCT for it?
  23. nothing can be done here at all?? (((

    nothing can be done here at all?? (((
  24. Powerstroke 6.4L - Cleaning Exhaust Filter - how to turn off??

    Ford F450 2008" Powerstroke 6.4L Diesel - we turned off many different DTC in the rom for EGR and DPF - no any Check light appear, but Dash shows up the message - Cleaning Exhaust Filter - and fuel...
  25. How to tune fuel AFR for WOT? for SRT8 2012" - 6.4L Hemi with SuperCharger

    How to tune fuel AFR for WOT? for SRT8 2012" - 6.4L Hemi with SuperCharger - there are VE tables but it do not work because of Neural Network activated i guess. According to description we need to...
Results 1 to 25 of 148
Page 1 of 6 1 2 3 4