Search:

Type: Posts; User: 96gt4.6

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds; generated 42 minute(s) ago.

  1. Replies
    13
    Views
    8,505

    Have you taken the advanced parameter training to...

    Have you taken the advanced parameter training to unlock the greyed out parameters yet?

    https://www.hptuners.com/emissions/
  2. Replies
    2
    Views
    687

    If you know the original OSID of the vehicle...

    If you know the original OSID of the vehicle (available if you open the stock tune and look), then you can create an association in the VCM scanner with that VIN so that it will load the proper...
  3. Well I was able to hear back from Whipple, and it...

    Well I was able to hear back from Whipple, and it sounds like the 2nd IMRC signal circuit is configured to be used as a BARO sensor, although it was never utilized, so adding any input on that will...
  4. Right, but there are two IMRC position sensors,...

    Right, but there are two IMRC position sensors, and the calibration only converts one of them into manifold charge temp (IAT2).

    The other IMRC position sensor connecter is just tied back, and has...
  5. '17 Mustang GT/Whipple Stage 1 OS Question

    I'm currently changing my fuel system over to a GT350 dual OEM pump setup, and was also going to add in a fuel pressure transducer so that I can monitor fuel pressure. My IMRC units are obviously...
  6. Replies
    23
    Views
    22,520

    The issue I had was caused by the PCM seeing...

    The issue I had was caused by the PCM seeing vehicle speed (had a speedometer conversion box installed). If there is any VSS shown, it will not read out.
  7. I have a question about using the Whipple OS........

    I have a question about using the Whipple OS.....

    It had been touched on earlier in the thread about how the guardian/flare tool makes modifications on the fly. I noted when I used this function...
  8. Replies
    8
    Views
    2,774

    Will do! Is there any way to get around this...

    Will do!

    Is there any way to get around this to use the Editor? Being as the OSID is scrambled, I'm assuming the file on there now is protected/proprietary is why the OS is scrambled.

    I...
  9. Replies
    8
    Views
    2,774

    Ah, very nice! That I was not aware, thank you! I...

    Ah, very nice! That I was not aware, thank you! I do actually know the OEM ID so I will give that a try.
  10. Replies
    8
    Views
    2,774

    Was there ever a solution to this? I'm running...

    Was there ever a solution to this? I'm running into the same issue....
  11. Finally got around to installing the transducer...

    Finally got around to installing the transducer setup and replacing my non PP one wire sender, so the oil psi is actually live in the data stream:
    ...
  12. GT sender is 1 wire, closes to ground when above...

    GT sender is 1 wire, closes to ground when above 10ish psi, no actual reading is produced from this sender.

    PP/350 Sender is a 3 wire pressure transducer, and must be wired into ground/vref and...
  13. Replies
    14
    Views
    4,208

    I just hit a couple of Ford and GM tunes and it's...

    I just hit a couple of Ford and GM tunes and it's all there....

    Can you provide a screen shot/cal file to look at? I also just updated to the latest Beta and re-checked.
  14. Replies
    14
    Views
    4,208

    Is this only for the front O2's it seems? Or...

    Is this only for the front O2's it seems? Or front, and rear's?
  15. Replies
    11
    Views
    3,826

    No luck here. Logging is horrendous at best....

    No luck here.

    Logging is horrendous at best. Causes cluster to blank out when MPVI2 is plugged into OBD port and attempting to log.

    Reads and Writes great! You just have to log with an SCT...
  16. Replies
    0
    Views
    1,313

    6R80 Anticipated Shift Logic and 1-2 shift

    So I have been reviewing some logs from my car (2017 S550/5.0L/Whipple), and noticed that at the track, the 1-2 shifts around 5-700 RPM early when I am on a tire and no wheel spin, vs if it spins any...
  17. Replies
    1
    Views
    810

    Please delete, found what I was looking for with...

    Please delete, found what I was looking for with a little more searching!

    Transferred the whole HP Tuners folder and we good :).
    ...
  18. Replies
    1
    Views
    810

    Transfer Scanner UPF File?

    I'm wanting to be able to setup log config files on a desktop PC that has never or can never be connected to a vehicle. Currently, the only thing I can do in the scanner is open a log file on that...
  19. Replies
    2
    Views
    1,923

    Will do! Thank you!

    Will do! Thank you!
  20. Replies
    2
    Views
    1,923

    How to tell if L5P PCM is already unlocked?

    I have a customer that has purchased a 2019 2500/L5P at auction, with what appears to be a new pcm installed (case is new looking/shiny, rest of the truck isn't). He is wanting to tweak a few things...
  21. Remote Logging and Adding PID's to create config file

    I'm trying to setup a config file so that I can have someone do a remote log. However, I'm having trouble doing so. Do you have to be connected to a vehicle 1st to set up the PID list? Or is there a...
  22. Replies
    0
    Views
    682

    L99 5th gen Camaro/LSA Swap IAT2 Scaling

    Looking for a little help on an LSA swapped 5th gen. Car has previously been swapped, but the IAT 2 sensor on the blower lid was not in use.....just the MAF IAT sensor.

    I installed the Ballinger...
  23. Replies
    15
    Views
    9,300

    CHT sensors are screwed into a hollow void in the...

    CHT sensors are screwed into a hollow void in the cylinder head casting, their sole purpose is to detect the temperature of the cylinder head metal itself. No oil or coolant is touched by the CHT...
  24. Replies
    3
    Views
    1,285

    It certainly appears the Whipple tune is looking...

    It certainly appears the Whipple tune is looking somewhere else for some parameters. Considering how much, and what you can change as far as parameters in the Flight Controls/Whipple software, there...
  25. Replies
    3
    Views
    1,285

    Whipple Flight Controls

    So I have been working on modifying the tune on my S550/Whipple setup, and I have a question perhaps someone has ran across before myself.

    So, with the Whipple flight controls, you can change the...
Results 1 to 25 of 491
Page 1 of 20 1 2 3 4