Update* so I message support and basically we came to the conclusion that the 42rle in my car can't be tuned.
Type: Posts; User: [email protected]
Update* so I message support and basically we came to the conclusion that the 42rle in my car can't be tuned.
I'm looking to see if there's any support in general. But mainly to see if there's a way to add some pressure to tcc apply tables and to see if there's any tables that can be looked at.
Hi, I have a 2005 dodge magnum with 3.5 and 4spd 42rle. I was wondering if these transmissions are able to be tuned at all?
still dies at idle.. i added more friction into transition to idle which helped it from dieing when coming to a stop. but still have misfire on 6 and when its under idle rpm when coming to a stop all...
So fuel pressure is good and I decided to check trans fluid level since I'm concerned about the trans might be the issue. The trans level was low so tomorrow I'm going to add fluid till its full and...
It's the file that was in it before all this happend . But I'm concerned that the trans mission is is responding to slow or just acting weird. So when it dies its in 4th gear at 5-10mph. And also I...
so tomorrow the splitter to test fuel pressure is coming in so ill check that. But today i did a about ten throttle relearns and did a data log to see if that would help. But can someone look at my...
i just really am confused. it still dies when coming to a stop and misfires. im just defeated. im about to check fuel pressure just to rule everything out.
so spray ram i put int your second file and it misfire still and it seemed to have shaken more in the cab
Ok sounds good.
It's a mellings replacement cam. Ik it makes more sense to have just put in any other cam rather than the stock mds one.. but honestly for me I just needed it up and running quickly because it's my...
I'll load it in either tomorrow or Friday because I have to put the intake back on because of unplugging the mds solenoids. But is there a reason to turn vvt off?
It doesn't make any sense. I did a continuity on the mds harness and that passed yesterday. But the tune I posted has been in the thing since last year with no issues. So I wouldn't think it was the...
I haven't messed with any cam/vvt tables in the tune I believe that's stock as far as I'm aware. I don't fully understand the vvt degrees so I haven't touched it.
so the vvt solenoid is a duralast part number ts1023. and ill disconnect the mds solenoids. ill post the tune. the tune is dummy down from when it had to pass emissions and started rounded off came...
It's the zf8hp trans and I'd say from it was parked for 2 months before I took apart to replace cam and lifters.
Your all good man I'm just trying to fix this and get it running lol. But yes the mds solenoids are replaced with plugs but I left the solenoids plugged in so the connectors wouldn't get corroded....
I have a scan tool that can monitor misfire counts for all 8 cylinders and it acts like a dead miss just keeps going up and then I drove it and the misfire count stops. But for the mds harness...
The gap on the plugs are correct and I checked the coil itself and it ohm checked it and the coil was fine and I even swapped coils to a different cylinder and the misfire stayed on cylinder 6. Even...
I did try cam sensor and that didn't help. The thing is it doesn't misfire or have any issues while drive or under load its just at idle and coming to a stop. I cleaned out the fuel rail to make sure...
Yes it doesn't matter if nn is on or off. I tried raising rpm to 750 and it will misfire less than it would around 600 but would still misfire and when coming to a stop it would still die. Then I...
I did swap lifters with cylinder 8 and problem p0306 is still there. I visually inspected the springs and non are broken. I checked wiring for coil and injector and I couldn't find any issues. No...
Ok, my thought processes was that if the truck had mds lifters and cam but mds turned off then it wouldn't matter if non mds lifters on mds cam because the lifters would still still roll over the cam...
hi, I have a 2014 ram with the 5.7 hemi and it had cam and lifter failure. I replaced cam with mds cam replacement with non mds lifters. I have mds turned off. after replacing it I have been fighting...
hi, I have a 2014 ram with the 5.7 hemi and it had cam and lifter failure. I replaced cam with mds cam replacement with non mds lifters. I have mds turned off. after replacing it I have been fighting...