Search:

Type: Posts; User: spoolboy

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Were the Hellcat tables fairly close to what you...

    Were the Hellcat tables fairly close to what you ended up with?
  2. If you log, I beleive you will find that most of...

    If you log, I beleive you will find that most of the cells aren't hit anyway.

    Also, keep in mind that the Scats do not have a factory wideband. If the car doesn't have and aftermarket WB...
  3. Have you seen this? ...

    Have you seen this?

    https://forum.hptuners.com/showthread.php?66353-Dodge-tuning-w-ANN-InjPW-v-Fuel-Mass-spark-advance
  4. I?ve heard people say the hellcat injectors don?t...

    I?ve heard people say the hellcat injectors don?t work well in the other engines. Also, copying the stock hellcat injector fuel mass tables directly over is not going to be dead on either based on...
  5. Looks like it's following the max TIP table? ...

    Looks like it's following the max TIP table?

    Try changing that around and see what happens.
  6. Replies
    16
    Views
    329

    If the baro learn doesn't do it, try setting the...

    If the baro learn doesn't do it, try setting the torque management>driver demand tables and throttle WOT and Pedal WOT all back to stock and see what happens. It looks like you may have something...
  7. The answer is probably no. But you can: Save...

    The answer is probably no. But you can:
    Save ?current? tune file.
    Flash back to stock.
    Have the dealer flash your vehicle with the update.
    Read/copy the dealer update tune file.
    Open the...
  8. It seems like the way to approach this is to...

    It seems like the way to approach this is to unhook the manifold pressure reference to the fpr and then dial in the VE.

    Then hook up the manifold reference and dial in the vacuum correction.
    ...
  9. Replies
    16
    Views
    329

    44450 make it 0 not 8160

    44450 make it 0 not 8160
  10. Replies
    22
    Views
    1,292

    Dredging this back up again. So the TMAP...

    Dredging this back up again.

    So the TMAP multiplier (44395 in my file) airflow>general>map estimation looks to be the table that allows for the calculated or estimated map based on rpm and mass...
  11. Replies
    7
    Views
    190

    Sometimes.

    Sometimes.
  12. Replies
    7
    Views
    190

    It depends. Different years are mapped...

    It depends. Different years are mapped differently.

    Post your .hpt file.
  13. Try unhooking the vacuum reference and...

    Try unhooking the vacuum reference and (carefully) make some runs and see if that is indeed the issue.

    What exact table are you talking about that is all 1s?

    I found 2 that could be the table...
  14. Replies
    1
    Views
    158

    Stock injector sizes?

    Lots of conflicting info out there on the google.

    What are the stock injector sizes?
    3.6
    5.7 (different years?)
    6.1
    6.4
  15. By vacuum multiplier, are you talking about the...

    By vacuum multiplier, are you talking about the row axis of the offset table?
    fuel>general>offset?

    On my 2016 Scat (stock tune) it is the same from 0 to 100kpa, which seems incorrect.

    Is your...
  16. Replies
    3
    Views
    232

    It wouldn't be unlocked unless someone sent it...

    It wouldn't be unlocked unless someone sent it out for unlock.

    2015+ are all locked.
  17. Will this cause issues? Re-mapping tables?

    Take a look at the before and after.

    If I do this, will it cause issues? Seems sketchy. Afraid to try it since I haven't seen it mentioned.

    Basically I'm directing a drive mode to a different...
  18. Replies
    13
    Views
    461

    There's a thread somewhere (I'd have to go find...

    There's a thread somewhere (I'd have to go find it) where Hemituna talks about the cam timing max/min and what the limiter allows.

    The PCM accesses different timing tables depending on where the...
  19. Replies
    2
    Views
    150

    The shift points are output shaft rpm. Just...

    The shift points are output shaft rpm.

    Just divide by the gear ratio to get approx engine rpm for the shift point plus allow a few rpm for the shift to complete.

    You can log which shift table...
  20. Thread: Power delay

    by spoolboy
    Replies
    3
    Views
    190

    Seeing any burst/throttle knock or retard? ...

    Seeing any burst/throttle knock or retard?

    Also check out the max demanded throttle voltage table under airflow>electronic throttle.
  21. Replies
    8
    Views
    251

    Did you recently change the valve body?

    Did you recently change the valve body?
  22. Replies
    13
    Views
    461

    You are correct if you are talking about the...

    You are correct if you are talking about the Intake center line, but these cams are adjusted based on the Exahust center line. And since there is only one cam, what he stated was technically correct.
  23. Replies
    8
    Views
    251

    No I don't think I know how to fix it. It's...

    No I don't think I know how to fix it. It's possible that something is hurt in the trans and it can't "grab" the next gear as quickly as it should. Clutch or band or something in the system that...
  24. Replies
    8
    Views
    251

    Is one pid (RPM) polling at a faster rate? ...

    Is one pid (RPM) polling at a faster rate?

    That doesn't make sense to me otherwise.
  25. Replies
    3
    Views
    399

    Post your tune file. Have you looked at the...

    Post your tune file. Have you looked at the fuel>temperature control settings? Anything changed in there on the first "tune"? Might explain the melted cats.

    The driver request & expected mode...
Results 1 to 25 of 183
Page 1 of 8 1 2 3 4