Search:

Type: Posts; User: 04colyZQ8

Page 1 of 17 1 2 3 4

Search: Search took 0.00 seconds.

  1. just use a E67 from a 2007 CTS-V only came in...

    just use a E67 from a 2007 CTS-V only came in manual, no vvt non boosted.. just swap in a LS2 TB, and use a CTSV pedal. tune it done:) I can flash it for you, I have gm software, and I am in Canada.....
  2. As far as the reverse lock out pin same location...

    As far as the reverse lock out pin same location on all e67s, c3, pin 8. But it?s not enabled in the pcm, again something I can do in raw hex
  3. You can use a ctsv file be a lot closer, I can?t...

    You can use a ctsv file be a lot closer, I can?t see why a/c would not work, cruise can be made to work using the ctsv file, but I would need to lock the file after, as that took me forever to find...
  4. I can do practically anything with an e67, I...

    I can do practically anything with an e67, I converted auto to manual.. the entire tune, reverse lockout , cruise 0-5 volt or discrete clutch input.
  5. Replies
    6
    Views
    6,940

    I?m sure it?s there under engine diagnostics

    I?m sure it?s there under engine diagnostics
  6. Replies
    41
    Views
    26,001

    The 8wire tb has two tps signals that move, in...

    The 8wire tb has two tps signals that move, in the same directions. With separate high and low refs, you can switch one high and low ref around to make both signals move in the opposite direction...
  7. Replies
    41
    Views
    26,001

    Really interested in this.. btw tech 2 scanner...

    Really interested in this.. btw tech 2 scanner gives a really nice look at the tps voltages
  8. Cannot richen up take off fuel letting out clutch 5.3l with cam

    I keep going lean missing and bucking after the stage 4 cam swap, wide band sees 16 and pegs there for a second or two?

    I?m only getting 50kpa at 9000 rpm idle spark 18-19, and base air flow...
  9. Replies
    0
    Views
    818

    Po106 stage 4 tsp cam 5.3l lh9

    2011 5.3l lh9 from a canyon. In a 04 Colorado with t-56, vvt delete, ls2 intake, ls2 tb, volant Intake long tube headers. With tsp stage 4 truck cam.

    Using a 2008 Hummer h3 pcm, I had this exact...
  10. Looking for a 2009 hummer h3 alpha 5.3l fscm read out file

    I need a fscm read out of the fuel module only from a v8 hummer h3. I?m switching from a 3.7l to a v8. The system segment on the fuel module is different from the 3.7l to the 5.3l
  11. Replies
    173
    Views
    259,181

    http://www.gmtruckcentral.com/articles/12200411.ht...

    http://www.gmtruckcentral.com/articles/12200411.html Email Lexi
  12. Replies
    173
    Views
    259,181

    I just did a 97 to 0411, 96 should be the same. I...

    I just did a 97 to 0411, 96 should be the same. I can tune the 96 pcm though. Why do you want to make the switch
  13. What year ctsv is that? Looks like it still uses...

    What year ctsv is that? Looks like it still uses the bcm??
  14. Ok great thanks:) what's digatel or anlalog...

    Ok great thanks:) what's digatel or anlalog option for fuel systems about??
  15. That's pretty cool! Did you sell the harness...

    That's pretty cool! Did you sell the harness after? So I wasn't the only one that noticed the connect and cruise had tutd:)

    What to poeple typically do for cruise with the gmpp kits?
  16. I am trying to develope a class 2 to can module,...

    I am trying to develope a class 2 to can module, but the less I have to do, the easier it will be, perhaps I can figure the reverse lights out also.
  17. I haven't tried that either as I don't have that...

    I haven't tried that either as I don't have that year bcm, I have a 2009 bcm. And the vin in that bcm was incorrect. It would be interesting if sps would poll the right bcm for the vin and then...
  18. It's to bad there isn't a way to custom code the...

    It's to bad there isn't a way to custom code the tcm into sending a ground signal to a relay for reverse lights
  19. 8L90e 6l80e 6l90e reverse lights in swap vehicles possible?

    I know some poeple fab up a manual reverse light switch, on a bracket for the 6l90e. But what about the 8l90e? I know there is a company selling a can based module for 220.00 and two relays for park...
  20. T87 8L90e equipped vehicles different gas pedal why?

    All factory applications use a different part number gas pedal for the 8 speed. Something to do with the 2nd gear downshift. Pedal has heavier feel near bottom of travel. And is suppsed to signal the...
  21. E92 pcm single use?? Cannot change vin or os, on used pcm?

    Tried flashing a couple different os into a e92 using gm sps, fails at 99%, won't write the new vin perminately? Looking at the raw binary for a e92, the vin is stored twice in the ecu flash! Looks...
  22. Replies
    3
    Views
    2,347

    Pretty sure it's the same for 6l90e and 8L90e....

    Pretty sure it's the same for 6l90e and 8L90e. Just use a t43 instead of the t87. There was factory 2014 5.3l with the t43, I should think you could just use sps to flash Both controllers.
  23. Thanks again:) see any issue running a l86 6.2l...

    Thanks again:) see any issue running a l86 6.2l with the lt1 tune? They both are 6.2l, same heads, injectors, tb, only Difference might be the electric oil pump, Intake, and cam?

    And I'm...
  24. Great thanks so pin 39 on the t87 controller?...

    Great thanks so pin 39 on the t87 controller? That's amazing how'd you find that out? I've called the dealer, gm help line, helms and searched. Everywhere. No one has wirring info for gmpp they all...
  25. T87 8L90E TUTD tap shift what pin to enable?

    I see that there is hardwire and TUTD enable, but what pin? I have a the resistive ladder diagram needed to make it work, from a GMPP connect and cruise 8 speed kit. But I don't have the harness or...
Results 1 to 25 of 403
Page 1 of 17 1 2 3 4