Search:

Type: Posts; User: BADWOLF

Search: Search took 0.00 seconds.

  1. Your not seeing it because its not there , looks...

    Your not seeing it because its not there , looks like its not supported on that OS..
  2. [ECM] 12283 - Fuel To Wall Impact Factor vs. Cool...

    [ECM] 12283 - Fuel To Wall Impact Factor vs. Cool Temp vs. MAP:
    I think its what your looking for..
  3. Replies
    14
    Views
    3,355

    . 4.4.2 Advanced view Do compare of a auto vs...

    .

    4.4.2 Advanced view
    Do compare of a auto vs manual file for your os , all other things being equal , lots of differences between a flywheel (energy storing) vs a converter (energy stealing)
  4. Replies
    14
    Views
    3,355

    Looks like the original tune was a manual, made...

    Looks like the original tune was a manual, made some adjustments..you may have to tweek the BRAF P/N
    90469

    Edit; The idle max P/N and BRAF alone might get it for you if the other parameters have...
  5. Replies
    6
    Views
    5,243

    Run it through the Bluecat Trans tool and use...

    Run it through the Bluecat Trans tool and use 5200 for Desired shift rpm

    https://forum.hptuners.com/showthread.php?44953-Bluecat-Transmission-Table-Software
    ...
  6. Is this what your looking for..? 02 Silverado...

    Is this what your looking for..?
    02 Silverado 4x4 4l60
  7. Replies
    9
    Views
    3,961

    [ECM] 730 - Starter Diagnostics Master Enable;...

    [ECM] 730 - Starter Diagnostics Master Enable;
    as stated in the first reply try setting it to Disabled
  8. Replies
    7
    Views
    3,802

    Try removing the channels, repoll for supported...

    Try removing the channels, repoll for supported parameters while connected to the vehicle, then add the channels back in.
  9. Replies
    7
    Views
    3,802

    When selecting Gauges click the gear icon in the...

    When selecting Gauges click the gear icon in the tool bar to show only parameters backed by channels ..

    For Battery Volts you can use control module voltage if a PO1/P59.. IIRC...

    As for...
  10. Use the Navigator Ctrl+N enter ECT 90309

    Use the Navigator Ctrl+N enter ECT
    90309
  11. Try Setting [TCM] 403 - TCC Enable Solenoid:...

    Try Setting [TCM] 403 - TCC Enable Solenoid: Master enable/disable for the TCC enable solenoid, to Enable
  12. Replies
    6
    Views
    3,943

    You need to be in Advanced View... 90277

    You need to be in Advanced View...
    90277
  13. Replies
    6
    Views
    3,943

    This is on OS 12212156-> RTT Enhanced so i dont...

    This is on OS 12212156-> RTT Enhanced so i dont know how it will translate to your Commodore OS

    [14200] is the channel in the Scanner and is labeled Trans Shift Mode and shows Normal,Power,Cruise...
  14. Replies
    17
    Views
    8,905

    Try setting P1626 and P1631 to no error...

    Try setting P1626 and P1631 to no error reported...
  15. Replies
    6
    Views
    3,943

    It's [14200] Trans Shift Mode on my po1 ..if that...

    It's [14200] Trans Shift Mode on my po1 ..if that helps
    There is also a setting under Trans>shift general for switch type, set to one switch...?
Results 1 to 15 of 15