Search:

Type: Posts; User: Lakegoat

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    68

    What computer? NA? Boosted? Return system? Non...

    What computer? NA? Boosted? Return system? Non return system?
  2. The 2-6-1 trans tune that you posted is nothing...

    The 2-6-1 trans tune that you posted is nothing like the original tune in the first post. According to your scan, you want it to shift at 55 mph---which it is. Your rev limiter is set at 6700 and...
  3. Replies
    7
    Views
    238

    You are not going to affect the springs with 8psi.

    You are not going to affect the springs with 8psi.
  4. Your highest map reading is only 94kpa. The...

    Your highest map reading is only 94kpa. The Primary VE table goes to 105. If you are na, you don't need a boost table. You have to smooth out your VE table. Where is your wideband input?
    You...
  5. Do you really want to shift at 5400rpm? At...

    Do you really want to shift at 5400rpm? At 5400rpm in first, you are at about 41mph. Your WOT shift point is 25mph. Probably too wide a spread for the computer. Try about 5mph less (36). Also in...
  6. Replies
    11
    Views
    307

    Go to Engine---Idle---Airflow---ETC Scalar and...

    Go to Engine---Idle---Airflow---ETC Scalar and change to at least 7,300.0000. This works for me, but I have seen some setups as high as 8,000.0000. At least now you know the range. You will have...
  7. Thread: Lean tip in

    by Lakegoat
    Replies
    15
    Views
    367

    Look at you maf curve in 2d. There is a big...

    Look at you maf curve in 2d. There is a big blip. Smooth it out.
  8. Replies
    7
    Views
    167

    Post up your tune and a scan if you have it with...

    Post up your tune and a scan if you have it with wideband input. Do you still run the maf ?
  9. Replies
    11
    Views
    307

    That's a scan---where is the tune? Got a...

    That's a scan---where is the tune? Got a wideband on that setup?
  10. Thread: Lean tip in

    by Lakegoat
    Replies
    15
    Views
    367

    Sounds like you need to fatten up a few cells...

    Sounds like you need to fatten up a few cells that you have identified as lean. Have you done that to your ve tables? Are you in SD? Where is your tune and a scan of the event? What kind of car?...
  11. Replies
    11
    Views
    307

    What year, make and model of car is this on. Is...

    What year, make and model of car is this on. Is it stock or do you have modifications. Post your tune. Cable or drive by wire throttle body?
  12. Replies
    11
    Views
    307

    Is this on your Kubota tractor?

    Is this on your Kubota tractor?
  13. Replies
    23
    Views
    1,600

    Batten down the hatches

    Batten down the hatches
  14. Replies
    15
    Views
    453

    Look at your spark and VVE table in the 3D view. ...

    Look at your spark and VVE table in the 3D view. Both of those should be corrected before you go changing other things.
  15. Replies
    7
    Views
    238

    Are you saying you are tuning your blower engine...

    Are you saying you are tuning your blower engine with no wideband? The fuel pressure needs to be steady also. What is your injector duty?
  16. Replies
    7
    Views
    238

    The tunes from Magnuson have to be 50 state...

    The tunes from Magnuson have to be 50 state legal. And--a lot of guys do their own install and then go out and beat on the car without checking anything in the tune. If the tune was set up close to...
  17. Go to engine Diagnostics and change P0121 enable...

    Go to engine Diagnostics and change P0121 enable to 250 and P0068 to 8000 and see if that works.
  18. Replies
    26
    Views
    618

    Does he still use the Maf ? Does he have a GTO...

    Does he still use the Maf ?
    Does he have a GTO gas pedal ?
  19. Your flow rate looks like a return system and...

    Your flow rate looks like a return system and your offset vs ingv looks like a non return system.
  20. Did you try to put the larger injector numbers in...

    Did you try to put the larger injector numbers in the chart? Some of the 2009 E38's accept up to 127#.
  21. Your injector duty at 6000rpm is 108% on run22. ...

    Your injector duty at 6000rpm is 108% on run22. Since the injectors cannot flow more than 100%, that could be a problem.
  22. Replies
    1
    Views
    124

    Turn off desoot while you are tuning. If you are...

    Turn off desoot while you are tuning. If you are running 58psi, I don't think your IFR table is correct for ID 850's. Smooth your ve table and manually push the sharp peaks and valleys back to...
  23. Replies
    26
    Views
    618

    I think the computer sends a ground signal to...

    I think the computer sends a ground signal to fire the injectors. May be a ground wire is left off somewhere.
  24. On LS1 Tech website, there is data for those...

    On LS1 Tech website, there is data for those injectors.
  25. Replies
    6
    Views
    248

    Did you change out your map sensor from stock to...

    Did you change out your map sensor from stock to a different one? At 6500 rpm, your map is at 79kpa? I would think it should be around 100+ if it is not boosted. At the same rpm, your commanded...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4