This table is more of a monitor or a clip from what I understand. If the vehicle cant reach 100% of the value it should trigger the under boost code. Im thinking if this is jacked up too high and it...
Type: Posts; User: supercowboy
This table is more of a monitor or a clip from what I understand. If the vehicle cant reach 100% of the value it should trigger the under boost code. Im thinking if this is jacked up too high and it...
optimum torque is how much is available of 100 percent. So 80% of power that the engine has. this allows you to control how much you can use. That's how I see it. Im only looking to increase 20...
To turn the boost up Is this correct. I'm just trying to get familiar with what I'm doing. I went back to a stock file and modified just minimal stuff. I kept increasing the tables by small amounts...
That fuel table is pretty much stock. I adjusted a little in the transition. The gl550 I have is completely stock. No modifications. The timing and fuel should not change much. I'm not trying to over...
Thank you. Here is the log. seams like I feel a clip or something. but kpa is still down.127206
Im tring to get the boost to go up but im failing at doing something. Ive played around with the optimum torque table and its not helping. Need some more direction on this. I would like to get this...
Here is another pull with the maximum load desired increased. I see it hitting the target at around 195 kpa. I also see a bit of knock retard also. looking at the lamda it did go down richer. Is that...
I loaded that map and it seems fine. Here is a log.
I would like to increase the boost some more. Maybe to about 200kpa. Not sure what the max is on this engine. Am I doing this correctly by...
Stock GL550 oem pull
Im getting a P1670-85 and a P061b-85 code. Seems like its a torque calculation thing. Does this mean Im hitting a torque clip or is this due to 2 tables not matching together. I have logged all...
I found 280 ish up in the higher rpm worked well. When I increased to 300 ish I was seeing more knock from the change. It would settle down with the advanced with lower values. The car would see...
I have noticed tuning on touring mode I have the MAF as tight as I can. When the car goes into track mode I noticed my trims go over -20 percent. This must be due to the open exhaust. Is there a...
yes this correct. This corrects the fuel volume to rpm across the table and brings it back into spec.
What I did was I copied over the LT4 SOI map. I took the whole map and decreased till I saw many 280-290 values in place. I wanted to keep the same shape. I have adjusted VVE map. I did notice the...
From my understanding the 32 percent increase in axis brings the resolution back in to the map and also corrects back to oem function.
You have to move it away from the exhaust closing. The...
Customer supplied parts. I didnt know the stock pump would handle the extra fuel for the heads and cam until after. The other thing I did not like was puck under the fuel pump. I thought this was not...
Im having a bit of confusion on how to set up the SOI fuel timing and fuel pump. Ive been watching Gregs video and trying to understand this.
Here is the setup;
2018 Camaro
Prc heads, Headers,...
Im having an issue setting a 2 bar sd tune flash. When I flash the car
after saving the file on 2 bar sdrtt my map sensor goes haywire. If I
reflash with rtt 1 bar enhanced flash and enter values...
looks like you pulled fuel from the maf table to compensate. I would shut of cot so that doesnt make changes. need some more data. datalog commanded afr in fuel settings make sure power enrich is...
If we disable in "tip in limiting" torque limit and etc limit, this disables all the tables underneath the disable boxes. So as I have it in the pic both those columns are disabled.
I pulled...
I have it set to 240 now still same
How much torque management is still in this car. Im back on the dyno now and it still cuts. I drove this car on the street with no cut. Getting frustrated. Here is a datalog
47302
Went for a street drive didnt get the cut pulled to redline. P0106 map sensor popped up. There must be a threshold im missing.
is there enough removed here or is there more to alter. Going down the menu is seems like most are a non issue in the torque management table. Car is a manual transmission also.47185
Im on the dyno tuning a 2011 ctsv. Installed lower pully (metco 8.6) and spacer lid. I tuned the car with smaller upper pulley and car made 575 whp. My afrs are 11.3 across the board. When we...