Search:

Type: Posts; User: jaker

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    2,568

    Even after the cable was fixed it still doesn't...

    Even after the cable was fixed it still doesn't work. Only the MPVI2 will connect. After all the drama the switches to turn on and off the VATS system failed to work. All I needed to do for the...
  2. Replies
    7
    Views
    2,568

    Bummer! What are my options from here? I have...

    Bummer! What are my options from here? I have $200 worth of Ford and Dodge credits on this cable yet.
  3. Replies
    7
    Views
    2,568

    Thanks for the response. 1. Still works in my...

    Thanks for the response.

    1. Still works in my 08 Suburban
    2. After cycling it reads: "controler unlocker: timed out"
    3. Power and grounds have been confirmed
  4. Replies
    7
    Views
    2,568

    Not that I'm aware of. Did you have any luck...

    Not that I'm aware of. Did you have any luck trying to resolve the issue?
  5. Replies
    7
    Views
    2,568

    2007 Crown Vic Failed to Read

    Equipment used MPV1 using 4.4.4

    Here's what I'm seeing, any help is appreciated.

    93309
  6. Replies
    6
    Views
    4,149

    Awesome, you've been a huge help! Thanks

    Awesome, you've been a huge help! Thanks
  7. Replies
    6
    Views
    4,149

    Been doing some research again on adding the...

    Been doing some research again on adding the sensor.

    This I thought was fairly informative even though it doesn't relate with trucks or my ecu....
  8. Replies
    6
    Views
    4,149

    Being in WI I'd love to keep running E85 in the...

    Being in WI I'd love to keep running E85 in the summer like I have in the past. It's been working OK so far but I did have some issues with it a few months back. LTFT's were +25 with e85 in the...
  9. Replies
    6
    Views
    4,149

    Virtual Flex Fuel and Headers E38

    I apologize if this has been previously covered, I did search for awhile. I have an 08 Suburban with flex fuel e38pcm and would like to do some long tube headers. Obviously the virtual sensor works...
  10. Replies
    10
    Views
    4,040

    Perfect, I'll look into that! Thanks I've...

    Perfect, I'll look into that! Thanks

    I've also been reading tidbits about top teir fuels. Chev recommends Chevron Techron and some people have verified it smooths idle. I can say it idles...
  11. Replies
    10
    Views
    4,040

    Played around today and this evening after work. ...

    Played around today and this evening after work. Here's what I have ended up with and I like how it feels and basically stays out of knock.

    I do have one complaint that I can't seem to work on...
  12. Replies
    10
    Views
    4,040

    It's been taking me a bit to get the VVE dialed...

    It's been taking me a bit to get the VVE dialed in and I finally have it finished. MAF tune goes quick.

    Just started messing with the PE, works pretty good except for the fact it doesn't...
  13. Replies
    10
    Views
    4,040

    Ah! I see. Thanks for the help guys. I'll...

    Ah! I see. Thanks for the help guys.

    I'll mess with it tomorrow and report back.
  14. Replies
    10
    Views
    4,040

    That was it! Thank you! I must have...

    That was it! Thank you!

    I must have completely overlooked the WOT portion of the PE graph.... Opps!


    See and issues with the knock going on there?
  15. Replies
    10
    Views
    4,040

    WOT Goes Rich, Throttle Tip in Knock

    I did some looking around the forum and to no avail on the WOT rich issue. I've looked at power enrich as well and can't seem to make that work to my ability either. Set at 55Kpa to start PE, but...
Results 1 to 15 of 15