The data has random delays so it's pretty hard to tell what is happening when, so you either let off first, or it cut power and you let off a fraction of a second later. By looking at it I'd say you...
Type: Posts; User: chevota
The data has random delays so it's pretty hard to tell what is happening when, so you either let off first, or it cut power and you let off a fraction of a second later. By looking at it I'd say you...
In that picture, where you have the line, I'd say you let off the gas.
Prior to that, on the far left where that double hump is, I'd say you hit the rev limiter. You hit it, it shut down, shifted,...
Do you have this selected?
143860
I had always assumed an HP tune did NOT correct the checksum, therefore I cannot pass smog in California where the smog station checks for that, but I'm just assuming.
So does it or does it not?
...
Here's my guess.
I'd lower my temps with the cooling fan too. No point in starting a run when the eng was as hot as possible. I also set the trigger to Water, no oil, so it responds quicker
...
All my channels are active on the screen, and all oem. Some are math, but based on oem channels. There are a others I'm recording too, but don't appear on the screen. Eg; knock sensor voltages...
That's a lot on the Torque to Load imo. Plus it looks like it kicks in abruptly?
What fuel are you using?
Fyi here's what my Scanner looks like, if you want to upgrade:
143593
https://forum.hptuners.com/showthread.php?98507-2017-C63S-File-Sought&p=693653&viewfull=1#post693653
For me, when floored, the throttle stays open and boost does all the work. Originally, however, the throttle would close too. It was difficult to figure out if the tranny was closing the throttle, or...
OkEvolution; I suppose you could check out the forum at MHH Auto. Lots of people in there with common mistakes, and lots of people who know a hella more than I do about this stuff, so maybe someone...
What do you mean by "I need to play with the OT and see if I can pull this out without sacrificing boost in the higher gears." Just curious really.
There is a forum; MHH Auto, that is kinda dark...
It won't hurt to try using the Scanner since it just reads. The patch to use the Editor is where people get in trouble. Bricking the ECU applying the patch is one, but I also wanted a copy of my ECU...
I will be of zero help, but maybe you/someone could explain why this RTD exists? I looked it up and it seems to be an HP version of MyGenius?
So it's for people who don't want to tune it...
It's fun trying to get answers outta this place huh? While I can't give you a 100% sure answer, I'll give you what I can:
HP claims it'll read data via the Scanner without the patch, which I...
Someone said they did, but I'm pretty sure it was a M157 or M278, not an M156. I remember it because we chatted about the ethanol % sensor he added. Could've been on the MBWorld forum. I'm all but...
I lowered my Nominal to 800 and it works nice. One day I may try to get full power with it back at 885, just to see if I can.
My Optimum Torque Monitor values are lowered ~5%, which helped. Also...
jacep, I thought you zero'd out the Opt Tq Monitors. I thought it odd but apparently it worked for you so I left it alone. So this was a tune you bought?
Your Optimum Torque settings would kill my car, so I set it how I would do it. Keep in mind that if does respond to that change I have no idea how much boost it might make because it is a big jump. I...
I asked because I couldnt really understand what you were saying
I assume your Eurocharge was loaded via MyGenius? Then you loaded the HP Patch and now MyGenius won't work?
If I remember correctly, after applying the HP Patch, MyGenius will allow me to load...
Any luck Rescu? It seems to me a lot of people pop in after buying HP, then we never hear from again. I assume they gave up? I hope you stick with it :)
I wish. I've give my left nut for that. Well, someone's left nut.
I've been wanting a trans tune for years, but problems include: Price, which imo is excessive for what you get. Taking the...
Now and then it commands a leaner than 1.00 Lambda while under load, and I can't figure it out. It doesn't happen often, but when it does the lambda varies between 1.1 to 1.7 lambda. It studders when...
Weancea; I assume that question was for me since we're just starting out with Rescu2000's tune.
My torque map is critical, and torque to load map is wonky but needed. If I set torque to load to 200...
I have a different ecu, but for me component protection is what I use. I have a base, or target map, and a 2nd fuel map. It apparently switches to 2nd based on exhaust temps, so I make target more or...