Search:

Type: Posts; User: G-Town-GT

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    2,951

    Hey Eric, any progress on this painful :banghead:...

    Hey Eric, any progress on this painful :banghead: front?

    regards Mark
  2. Replies
    2
    Views
    671

    2020 GT500 Speed Limiter patch ?

    Even thogh that I bump up all speed limits in the speedo tab, still having no sucess getting it over 300km/h
    Throttle shuts at around 295 Km/h.

    Is there a speed limiter patch like in the GT's...
  3. Replies
    11
    Views
    2,951

    Oh I was thinking this is most probably supported...

    Oh I was thinking this is most probably supported already as they are on the market in Australia and Europe already. But obviously not by now.
    I already have 6 requests by now for tuning them.
    ...
  4. Replies
    11
    Views
    2,951

    2023 Ranger Raptor 3.0 stock read anyone ?

    I wonder if anyone could post a stock read of the 2023 3.0 Ranger Raptor

    THX in advance
  5. 2020 GT500 P061A code after non clutched Pulley install

    Hey Guys,

    can someone point me in the right direction please for this issue.

    I know it is a issue with the now changed desired and actual torque and most probably the IPC is not satisfied with...
  6. Replies
    24
    Views
    4,289

    Under Vehicle Tab -> repoll for supported...

    Under Vehicle Tab -> repoll for supported parameters
  7. Yes clear KAM and perform the adaptive learning...

    Yes clear KAM and perform the adaptive learning drive cycle on a level road surface.

    1. Using the scan tool, clear the DTCs (Diagnostic Trouble Codes) and Transmission Adaptive
    Tables.
    2. Drive...
  8. New Ford approach? Brand new Mustang 10R80 OEM EU Strategy no longer goes PE

    Today I had a car in, that was just recently these days supplied with a Ford PCM/TCM update (LR3A-14C204-AAD).
    No tune, stock Car directly from the dealership.

    Besides that we all know, Ford has...
  9. Replies
    25
    Views
    12,854

    Your actual load is limited by your Torque tables...

    Your actual load is limited by your Torque tables causing throttle Angle source to be "TQ red. < Driver Demand" and as a result Driver Demand Limit Source will be "Comb. Stab. Limit"
    After this is...
  10. 97382 This is the latest stock EU Strategy ...

    97382

    This is the latest stock EU Strategy

    Gruesse nach Muenchen
  11. Replies
    8
    Views
    2,315

    yes looks like it

    yes looks like it
  12. Replies
    20
    Views
    15,323

    Yes correct, and also do not set the time to...

    Yes correct, and also do not set the time to infer to 0. I figgured that it will not mature if anything below 1 is set in this field. On our 18 F-150 time is 20s and Ego is set to 5 Stock, works for...
  13. Replies
    20
    Views
    15,323

    Your Inference [21230] and Closed Loop Table...

    Your Inference [21230] and Closed Loop Table [11525] are not properly setup. Your Y-axis values 9.0 and 14.6 with 100 to 0 percent are to broad for accurate and fast alc.-content calculation.
    They...
  14. Replies
    27
    Views
    12,185

    You are hitting Combustion Stab.-limit and...

    You are hitting Combustion Stab.-limit and injector limit.
    I attached a modified file for you to test.
    96704
  15. Replies
    713
    Views
    539,617

    Sticky: Giessen Hessen Germany :burnout:

    Giessen Hessen Germany :burnout:
  16. Replies
    3
    Views
    2,125

    Set [ECM] 44780 - Torque Limit Timer from 2sec to...

    Set [ECM] 44780 - Torque Limit Timer from 2sec to 255sec
  17. post a log with all limit sources. [EDIT ] I...

    post a log with all limit sources.

    [EDIT ] I just see your other post
  18. Yes indeed this is also my opinion, Boost spikes...

    Yes indeed this is also my opinion, Boost spikes only happen if the turbos are overspooled due to either missconfigured WG values or just maxing out parameters like TIP or turbocharger pressure...
  19. --SOLVED-- 2018 F-150 3.5 Ecoboost getting short lean request during WOT

    Hi,
    got some nut to crack here. During a WOT pull car is entering Stoich for a short period.
    Torque Source is driver demand throughout the complete Pull, you will also see some Popcorn and...
  20. Hey Darek, very nice :-) How about the 1.0...

    Hey Darek,

    very nice :-)
    How about the 1.0 ltr three Cylinder Fiesta's ?
    We have Thousend of them here in Germany.
    Any plans on supporting that?
  21. Ok, thanks Guys, I gave it a shot with my first...

    Ok, thanks Guys,
    I gave it a shot with my first mapping:

    Mapping is mainly Roush based with no MAP Sensor. SD, Spark, TQ, MAF and all relevant limiter tables are as of Roush calibration. Whereas...
  22. 2018 - 2650 Roush S/C MAF to MAP EU version

    some of us in Germany are obviously tuning the roush kit through SCT with MAF instead of MAP, and they claim that it would not work with MAP as roush has foreseen it in their kit and per their...
  23. Replies
    25
    Views
    10,050

    MCT Switch ECM 2559 under Engine diagnostics...

    MCT Switch ECM 2559 under Engine diagnostics General - set it to enable if you are using VMP IAT harness.
  24. Replies
    2
    Views
    2,897

    Pulled the plugs - wrong heat range - one tip...

    Pulled the plugs - wrong heat range - one tip melted - Plugs replaced 3steps colder - all good.
  25. Replies
    2
    Views
    2,897

    VCT Schedule Mode goes to disabled ?

    We have a Build Coyote with 6R80 making about 850-900 HP, car drives great so far and makes nice power.
    After some testing on the road for further dialing it in, and after the third pull while...
Results 1 to 25 of 102
Page 1 of 5 1 2 3 4