Search:

Type: Posts; User: Robert00MustangTurbo

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    42
    Views
    20,198

    Unfortunately, you'll have to yank em back out. ...

    Unfortunately, you'll have to yank em back out.

    It's crazy to me that these cams are still having this issue.

    I've just been doing full custom locked cams (MHS, MMR, etc.) and never looked...
  2. Fixed!

    We got the issue fixed!

    So thinking we have a cam/valve spring issue, the stock cams and valve springs were put back to stock. The issue still was there!! Looking deeply through the log, the MAF...
  3. Even though I didn't hear valve floating, that...

    Even though I didn't hear valve floating, that definitely makes more sense than cam profile, like valve spring stability issues. Literally feels like you hit a wall at that RPM.
  4. I reduced the amount of pids logged. Also the WOT...

    I reduced the amount of pids logged. Also the WOT Box was removed to eliminate a potential interference.


    The car pulls hard up until 5900-6100rpms then it falls on it's face. Throttle blade is...
  5. 2014 Mustang GT Cammed EBT Drops to 280 and hits a wall WOT

    Hello, I am struggling to get this vehicle to stay wide open and wondering if I'm missing something.

    2014 Mustang GT
    PMAS CAI
    Ported Cobra Jet
    VMP Twin 67mm
    Todd Warren Cams 240/242
    Degreed...
  6. Replies
    41
    Views
    17,049

    From what I've seen so far, the Tri-Core Series...

    From what I've seen so far, the Tri-Core Series PCMs (2015-Current Coyotes) flex fuel does not have tables 44574 and 44575 due to a completely different operating system, compared to the Copperhead...
  7. Replies
    41
    Views
    17,049

    I have had similar issues with some 2012...

    I have had similar issues with some 2012 Strategies where tables were flat out missing, even the RPM patch would be missing with the latest beta available. I just write entire a whole different...
  8. Replies
    41
    Views
    17,049

    Hello, I ran into the same issue with a 2012...

    Hello,

    I ran into the same issue with a 2012 Mustang GT M6 with flex fuel enabled. As soon as it went above 60% Ethanol, Cold Start Emissions reduction hammered timing to 0 Degrees.

    Reading...
  9. So after many hours on the dyno and road tests,...

    So after many hours on the dyno and road tests, I've finally got the car dialed in.

    NOTE: This is what worked for me. It may not work for everyone or they have their own method.

    1st problem...
  10. Unfortunately I haven't figured it all out, but I...

    Unfortunately I haven't figured it all out, but I did get it to idle Via Torque tables. It was the only table that would work.


    I still have a lot of work to do on this calibration in the torque...
  11. Okay, I removed the 103mm throttle body and...

    Okay,

    I removed the 103mm throttle body and Installed the stock throttle body (Older style 2650 that accepts Stock Throttle Body)

    Throttle body data is back to stock

    Majority of the errors...
  12. The Edelbrock 103 Throttle Body Data would be a...

    The Edelbrock 103 Throttle Body Data would be a great help, since I do not have that on hand.

    109098
    109099

    I was busy here at the shop, but I was able to squeeze some time into adjusting the...
  13. 2015 Mustang GT MHS Race Cams Idle control issues

    Hello,

    I am struggling with idle control with this particular setup.

    2015 Mustang GT M6

    Edelbrock 2650 Supercharger Kit
    Edelbrock CAI
    Edelbrock 103MM TB
  14. Replies
    42
    Views
    20,198

    Any MIL Codes? Those will be the tell tale if you...

    Any MIL Codes? Those will be the tell tale if you have issues with the camshafts right off the bat.



    And did you follow these very steps that most people miss?
    108563



    Lastly, is it...
  15. Replies
    3
    Views
    1,990

    On the same boat here for TB data

    On the same boat here for TB data
  16. I raised 38136 Inverse Load Clip to 4.0 and...

    I raised 38136 Inverse Load Clip to 4.0 and raised max map in the combustion stability value 44821 to 70. We're not hitting the Combustion stability limit anymore but now hitting Trans Truncation and...
  17. SCT for this particular PCM Strategy has the same...

    SCT for this particular PCM Strategy has the same limit for map combustion stability.

    107390




    Here's a screenshot of where map is at

    107391
  18. On the other logs I have on my laptop at work,...

    On the other logs I have on my laptop at work, they'll peg at 70inHg and air load would be around 2.60, so I can see trying to enter a higher value may work. I'll have to check on Advantage as well...
  19. Replies
    42
    Views
    20,198

    I'm happy to share because I want people to be...

    I'm happy to share because I want people to be aware of what occurred with that issue. I was tearing my hair out on that one. Talk about a relief when the dreaded ticking/clacking stopped :chug:
    ...
  20. Replies
    42
    Views
    20,198

    Unfortunately the customer provided the...

    Unfortunately the customer provided the camshafts.

    However, with the report I provided, Comp Cams did send an RMA to replace the camshafts. Customer has sent them out and got a new set, but I have...
  21. 2014 Mustang GT500 Whipple 3.8L 150mm Throttle Body issues

    Hello,

    I was tasked to dial in this 2014 Mustang GT500 with the following modifications:

    Whipple 3.8L Supercharger with Whipple 150MM Roval Throttle Body
    3.75 Pulley
    ATI 15% Dampener
    JLT 148...
  22. Sorry it took quite some time to get back to this...

    Sorry it took quite some time to get back to this thread,

    I was able to fix the issues. it's all related in the trans side of tuning.

    There were more areas I had to work on to get it to stop.
    ...
  23. So after taking the time to carefully read the...

    So after taking the time to carefully read the existing threads about the 10R80 on here and applying changes, I was able to stop the Trans FMEM, P0600 and P27B5 from occurring.

    I was able to...
  24. 2020 Mustang GT 10R80 FMEM 6th gear on the dyno and the street

    2020 Mustang GT 10R80

    Cobra Jet Intake Manifold
    Steeda CAI
    CFM Twin 67mm Throttle Body with JMS Throttle Max (If anyone has good TB Data for this throttle body or a Twin 65mm for the 2018+,...
  25. Here's a dyno graph on my 2012 Mustang GT with...

    Here's a dyno graph on my 2012 Mustang GT with 174XXX miles with the following modifications:

    2012 Mustang GT M6

    Ported Cobra Jet Manifold
    D-Mark Cold Air Intake
    VMP 137 Monoblade
    BBK Cat...
Results 1 to 25 of 63
Page 1 of 3 1 2 3