Using the segment swap tool fixed the problem.
It seems that the tool does more than you can do with the GUI and the settings in the transmission section.
I used a 99 MN6 file with the same OS...
Type: Posts; User: custosonlinux
Using the segment swap tool fixed the problem.
It seems that the tool does more than you can do with the GUI and the settings in the transmission section.
I used a 99 MN6 file with the same OS...
OK I'll try that.
When using the Segement swap tool, will it do other things than I can do in the GUI when copying settings and tables from one os to the other?
This is what the scanner shows when PCM is in manual mode. Voltage is shown but transmission temperature is not calculated
61949
no ideas?
Hi
I've a question about the PCM (or configuration) of a 99 Corvette C5.
I've done a A4 to MN6 conversion at my car.
Everything is fine and I change the parameters in the original A4 OS to the...
Hi there,
I'd like to give you an update about the problem I had with the power loss at 4500 U/min.
First of all: It wasn't a problem with the transmission.
Because of the way, my tuner...
What do you mean with "the car acts normal"?
Please explain.
Yes you can flash a A4 image to a M6 PCM.
Could you tell something more about your intention?
Tranny swap?
Thanks!
Wohow... seems like a hard calibration.
I'll try it, but I think I will let some mA in the 61-100 fields than setting it to 0.
I see that you set the shift times to values between 0,5...
Hello,
last Weekend I had time to do some tests and to check every hint and idea I got from you and RPM Transmissions.
First I checked the fluid level. -> It's OK, little fluid trains out when...
Hi,
is there a way to recalibrate the tables for the torque calculation?
I think after installing the Supercharger, the PCM is not calculating the right values for delivered torque.
When I compare...
Hi, yes I'm using electronic controls.
What do you mean with 42lb injectors? For the engine? Installed are 60lb as delivered with the A&A kit.
Hmm anything wrong with my question?
No ideas?
anyone?
Hi,
I know this thread is four years old, but I'm having the same problems.
What are your new settings?
Hi,
I need help to find the right values for my new installed transmission.
It's a RPM Level V with tripple disk lockup PI 2600 stall converter.
The car is making about 505 RWHP and 533 lbft...
Hi,
the stock Tune is mine.
TCC shift lock was enabled stock!
I disabled it in my future tunes, but stock it was enabled!
It seems that GM changed this value to disabled in future versions...
Ah, I see.
So there is no way to set WOT at 85% or 90% throttle and normal below 80% ?
Hi,
where are the settings for using the WOT tables for the A6.
At the A4 there were two parameters for "Full Throttle Enable"; Enable TPS and Disable TPS.
How can I adjust these on the A6...
Is it possible to copy the 08 trans settings into a 06 VCM?
What are the main changes?
Please have a look at this Thread: http://www.hptuners.com/forum/showthread.php?t=8887
Install the Performance Mode Switch and set up the Performance Tables to shift into the highest gear you allowed with the Gear Selector of the tranny (sorry I don't know the name for it. The selector...
Hi,
I want to open the hpt Files, but I can't see all the Torque parameters.
Do I need a special Beta Version of the HPTuners Programm?
Kind Regards
Birger
The Problem is, that if you turn off the ignition, the PCM resets to the "normal" Tables.
You have to reset the relais, too.
I've build a simple circuit with a IC 4020 and some resistors and one...
This is possible if you use the right settings and values for the performance mode tables.
I'm using this feature in my car. (just one switch for performance mode)