Search:

Type: Posts; User: porter84

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    979

    Ran over my MPVI2 today.

    A combination of my own stupidity and getting help from my 7yo boy....
    It got sat on the fender instead of put away, and when we headed out for lunch it got deposited in the road in front of a...
  2. Replies
    0
    Views
    1,264

    PCM Swap - NGC4A & NGC4

    I lost the PCM in my 2011 Wrangler and It's a single year PCM, from my limited knowledge and copious amounts of reading.

    I have an '08 Commander PCM, and was curious if I could try setting up a...
  3. Replies
    2
    Views
    730

    2005 Stock

    I Flashed this one with a Micropod II just before reading it out. It's an '05, but I'm not aware of any major differences they're both NGC3 SCI.
    Calibration notes with file: "AUTOMATIC WITHOUT 244...
  4. Replies
    8
    Views
    4,760

    I Just found myself struggling with this same...

    I Just found myself struggling with this same issue before reading the fine print under the supported vehicles list... I grabbed a NGC3 for an '05 (verified all my connector pinouts), programed VIN...
  5. Replies
    6
    Views
    1,854

    It has a Huntsville JTEC+ with 3 plugs. I'm...

    It has a Huntsville JTEC+ with 3 plugs. I'm thinking of taking a page out of Ford's EEC-V book and mounting a 32 tooth reluctor wheel to a 4.7 harmonic balancer and a crank sensor on a bracket. Then...
  6. Replies
    6
    Views
    1,854

    The '05 PCM still uses the PCI bus and works. I...

    The '05 PCM still uses the PCI bus and works. I have an 05 PCM running an 03 hemi in my 2001 Dakota trail truck.

    Although it's most likely possible, I doubt anyone capable has a reason to spend...
  7. Thanks. It doesn't hurt to hope. Could've saved...

    Thanks. It doesn't hurt to hope. Could've saved me a good chunk of change
  8. Thanks Bill. Looking at the Supported Vehicles...

    Thanks Bill.

    Looking at the Supported Vehicles list, it's clearly shown. When I was looking at this list before I purchased my unit I didn't realize this type of licensing was available for some ...
  9. Replies
    6
    Views
    1,854

    Well, I was hoping this would be straightforward...

    Well, I was hoping this would be straightforward wiring project, but it requires a 32 tooth crank wheel and can gear.... If I'm messing around with all that I'll just put a 2003-2008 hemi in at the...
  10. Year/Make/Model type purchase rather than individual credits.

    I saw somewhere that you can buy support for a particular year/make/model for 5 credits(or something to that effect)

    I have several 2005 Ram PCMs. I swapped my project truck with a 5.7 and used a...
  11. Replies
    6
    Views
    1,854

    I rigged up a bench harness and read out of of my...

    I rigged up a bench harness and read out of of my PCMs. I can't find anything related to crank/cam trigger counts or scaling.
    I saw a couple posts that reference scaling map sensors that state...
  12. Replies
    6
    Views
    1,854

    2005 NGC3 HO/Non-HO 4.7 interchange?

    I am contemplating a PCM swap in my 2002 4.7 Durango.
    It has a non-HO 2002 4.7 which I think should have 16 teeth on the reluctor.
    The PCM I have is a 2005 RAM 4.7 which I believe expects 32...
Results 1 to 12 of 15