Search:

Type: Posts; User: Mood1977

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    775

    6l80e tcm programming

    It?s my understanding that a gm reman trans comes with a tcm that has to be programmed with the gm software. I?ve been told that it can be done with hp tuners but some say that it can?t. Can anyone...
  2. Replies
    0
    Views
    514

    Tcc duty cycle not following min in tune

    This is a 2000 4896pcm. Duty cycle is not following the 99/100 in tune. It seems to follow it for the first few miles at 55 mph. Around 10 miles into the drive, it slowly decreases to 30% range. It...
  3. Replies
    3
    Views
    2,047

    How many Credits to license 2019 duramax

    I?m needing to correct speedometer. How many credits will be required to license 2019 duramax?
  4. Replies
    14
    Views
    2,254

    No dtc. When I manually turn it on with scanner...

    No dtc. When I manually turn it on with scanner it stays on. When it locks up on its own, it locks and unlocks repeatedly. I’ll log it tomorrow. I keep reading about misfires or false misfires...
  5. Replies
    14
    Views
    2,254

    Ok. I’m suspecting misfires are being detected...

    Ok. I’m suspecting misfires are being detected causing tcc to unlock. Will a Data log of tcc misfires show this? When this happens, how do I go about adjusting these tables?
  6. Replies
    0
    Views
    618

    Using scanner to control tcc

    Im trying to use the scanner to control the tcc. There is TCC PWM LOCK/Unlock on or off, and there is TCC Solenoid on or off. Could anyone that uses these functions explain their purpose? When I...
  7. Replies
    0
    Views
    653

    Tcc command on

    I?m wanting to command the tcc to stay on. I?m looking at the controls and special functions. There is TCC PWM LOCK/Unlock on or off,
    TCC Solenoid on or off


    When I command TCC PWM LOCK/Unlock...
  8. Replies
    14
    Views
    2,254

    Maybe 200 rpm. I’m looking at the controls and...

    Maybe 200 rpm. I’m looking at the controls and special functions. There is TCC PWM LOCK/Unlock on or off,
    TCC Solenoid on or off
    I’ve probably been going about it wrong. I’ve been using the first...
  9. Replies
    14
    Views
    2,254

    I know. It turns off when commanded on.

    I know. It turns off when commanded on.
  10. Replies
    14
    Views
    2,254

    Yes sir. When I command it “off” it locks and...

    Yes sir. When I command it “off” it locks and stays locked. So something is causing it to do this in the controls?
  11. Replies
    14
    Views
    2,254

    I think minimum is 99%.

    I think minimum is 99%.
  12. Replies
    14
    Views
    2,254

    I am going to try that to be certain today. I...

    I am going to try that to be certain today. I have a pressure gauge on it as well. Just got back on it this weekend.
  13. Replies
    14
    Views
    2,254

    2000 p01 line pressure

    So I?ve got a issue with the tcc locking and unlocking repeatedly around 55 when trans is hot. It appears to be commanded on the whole time. It don?t do it above 60-65. It?s got an ac delco reman...
  14. Replies
    2
    Views
    587

    Ok. No code yet. Going to investigate more today....

    Ok. No code yet. Going to investigate more today. Thank you.
  15. Replies
    2
    Views
    587

    2000 gm p01 cam sensor signal

    I?ve got a very strange situation that started with a quick 1 or 2 second dip in idle. Sounded like it was going to die then cleared up and ran normal. Now it has progressed to all the time. Engine...
  16. Replies
    2
    Views
    659

    Can anyone confirm the best source of ground when...

    Can anyone confirm the best source of ground when wiring the 0-5 v wb through egr? Does the original egr wiring ground through the pcm?
  17. Replies
    2
    Views
    659

    Analog wideband through egr

    I?m in need of some assistance setting up a graph to log afr. I?ve read some here and there. Is there a solid how to on here? Thanks
  18. Replies
    1
    Views
    2,148

    Beta vs stable

    I am unable to resync interface. I?ve been told to update software but I?m not sure which one to use. Beta or stable. Which is preferable?
  19. Will do. Which one? Beta or stable?

    Will do. Which one? Beta or stable?
  20. I updated drivers. No help. I’ve got editor...

    I updated drivers. No help. I’ve got editor version4.5.874 beta. Should that be updated? If so, which one? Beta or stable?
  21. How do I go about updating?

    How do I go about updating?
  22. Resync failed. Client version not supported.

    Trying to add credits. I?m getting this: Resync failed. Client version not supported. Does this mean I need to update? Thanks
  23. Replies
    3
    Views
    1,186

    I’m trying to dial in base running airflow. I...

    I’m trying to dial in base running airflow. I have seen where a graph was made where you basically copy and paste the data from it to the base idle airflow table.
  24. Replies
    3
    Views
    1,186

    Base running airflow

    Which airflow channel needs to be used to make a graph to log idle airflow? Idle desired airflow? Mass airflow? Thanks
  25. Replies
    15
    Views
    2,723

    Should this be done before the idle airflow...

    Should this be done before the idle airflow tables have been properly set up?
Results 1 to 25 of 82
Page 1 of 4 1 2 3 4