Search:

Type: Posts; User: xtantaudio

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    818

    L5P ECU Read File Request

    Hey everyone ! Looking to see if anyone has a stock ECU Read from an L5P ECU. My truck is a 2021 GMC 2500HD L5P. I just want to take a look at the stock file. Unfortunately/apparently I am not...
  2. jaydubb71, I received your e-mail earlier...

    jaydubb71,

    I received your e-mail earlier today. I will look through stuff shortly.

    As for the enhanced datastream, I do not have that option as an OS patch unfortunately.

    As for knock, I...
  3. Snyper, I believe that you need to submit an HP...

    Snyper, I believe that you need to submit an HP Tuners Support ticket for this. Currently I am not able to log knock for my 2012 FX35, I see it under parameters, but not under channels. I have...
  4. Nissan/Infiniti Tuning - Info Sharing & questions

    Hey everybody. This may be a long post, but here we go.

    I just started working on a 2012 FX35. ECU read wouldnt open - HP Tuners support fixed that. - Thank you

    Next, I noticed that the 2012...
  5. Replies
    4
    Views
    5,372

    b3tuning, Did you ever get a response to this?...

    b3tuning,

    Did you ever get a response to this? I have just started diving into the Nissan stuff and I have noticed that there isnt even a PID in the VCM scanner for the vehicle I am working on to...
  6. Replies
    2
    Views
    1,964

    Infiniti FX35 Tune - Stock Read

    Hey everyone !

    I noticed that the ability to load tunes to the HP Tuners repository is not possible right now, and I want to help get the nissan tuning stuff up and going.....

    Here is the stock...
  7. Sticky: IARLLC, did you ever receive a response to your...

    IARLLC, did you ever receive a response to your Validation Checksum Failed issue ? I recently submitted one for a 2012 FX35, was hoping to be able to get some tuning done on it.
  8. sgod1100, yes, I believe that from the start of...

    sgod1100, yes, I believe that from the start of the MAF tuning to now I have increased the values over 5000 Hz by almost 150 to 180% over the stock values. I just didn't think that I would have to...
  9. SultanHassanMasTuning, I increased the MAF...

    SultanHassanMasTuning, I increased the MAF Calibration table by another 40%. Finally getting positive results.

    I just found it hard to believe that the numbers had to be raised by almost 120%...
  10. SultanHassanMasTuning / TCSS07, I changed the MAF...

    SultanHassanMasTuning / TCSS07, I changed the MAF Table, Spark High and low Octane tables and well...... it is still showing a commanded ratio of .789 or so, and the wideband is reading 1.2 Lambda...
  11. I will take a look and give a try. I have the SD...

    I will take a look and give a try. I have the SD Tune dialed in pretty well, no lean condition there.

    I was under the impression that the enable /re-enable had to be set to 200 / 100 RPM for...
  12. New drive and some new data. Car is running a...

    New drive and some new data. Car is running a bit better, I followed instructions and lowered the re-enable to 100 RPM, and raised the MAF Table above 6000HZ by 25%

    I am still seeing that UNDER...
  13. sgod1100, Thank you for the recommendation. I...

    sgod1100, Thank you for the recommendation. I will give this a try as well and report back !
  14. Yes, that is what I am trying to do, is tune the...

    Yes, that is what I am trying to do, is tune the MAF, however when I run the car as it is now, I get bucking and hesitation. I will try changing the re-enable setting to 100 instead of 3800 in the...
  15. This is the issue that I am having trouble with,...

    This is the issue that I am having trouble with, the commanded AFR is 11.X, but the wideband is showing that the car (ECU) isnt actually making the injectors do it, and going lean. I will be trying...
  16. Yes, I need to work on that. There was a little...

    Yes, I need to work on that. There was a little knock around that area, so I removed some timing, until I get around to working out if it is false knock first. The knock sensors are not in the same...
  17. TCSS07, I will give this a shot tomorrow evening...

    TCSS07, I will give this a shot tomorrow evening and see what I can get to happen.
  18. 87382 I am seeing a 11.16 AFR or .789 PE...

    87382

    I am seeing a 11.16 AFR or .789 PE Commanded value, but the WB is showing that it is stuck at 1.4 lambda. Where are you seeing 17 AFR Actual? Am I really missing this ?
  19. The wideband is reading 1.0 to 1.2 lambda most of...

    The wideband is reading 1.0 to 1.2 lambda most of the time when PE was engaged at a value of .789. The wideband is the AEM Can Bus unit, has only been installed for about a week. One wideband on...
  20. Help needed - E67 CTSV Tune - PE working but Wideband not showing change

    I have completed the SD tune and the car runs GREAT. No hesitation, stalling or bucking, PERFECT Idle, even with the larger Cam.

    I have disabled DFCO and COT (no cats on the car anyways) and...
  21. 5FDP - Yes, I do need to work on smoothing that...

    5FDP - Yes, I do need to work on smoothing that out quite a bit. I will do some more drives and see if I can get that done. I appreciate your input !

    Does anything else stand out as "off" or...
  22. Another "Please check my log and tune" post. Opinions/feedback appreciated LSA setup

    Hello everyone. This is my first post. I have been a lurker/learner for a while now. Hoping that my learning has led to a decent start to a tune.

    I am hoping that someone can take a look at the...
Results 1 to 22 of 22