Search:

Type: Posts; User: 1278342005

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    3,802

    it was a kit and I've called the company that...

    it was a kit and I've called the company that made them and they have ZERO information on their injectors used unless you have the order number. Kinda b.s. but it is what it is.
  2. Replies
    16
    Views
    3,802

    I don't. That's the crappy part. I have no idea...

    I don't. That's the crappy part. I have no idea what injectors are in it. I know they aren't the stock injectors.
  3. Replies
    16
    Views
    3,802

    The map sensor that is in it, is a MOPAR sensor...

    The map sensor that is in it, is a MOPAR sensor that is a 2 bar. I suppose I didn't explain that right. It's the one they use in ProCharger applications. Not stock SRT8
  4. Replies
    16
    Views
    3,802

    The SRT8 is a 2 bar map. Everything I looked up,...

    The SRT8 is a 2 bar map. Everything I looked up, including a stock tune, shows a 2 bar setup.
  5. Replies
    16
    Views
    3,802

    This was a vehicle that a customer brought to me....

    This was a vehicle that a customer brought to me. It HAD a tune on it before from the company that installed it years ago. When he took it into the dealership for a bad MAP sensor, the idiots...
  6. Replies
    16
    Views
    3,802

    MAP sensor is a 6.1L SRT8 MAP.

    MAP sensor is a 6.1L SRT8 MAP.
  7. Replies
    16
    Views
    3,802

    JK Goes into Limp Mode MAP Issue???

    I've got a 2008 Jeep Wrangler that was brought to me with a Limp Mode Issue. Went through everything and tried just about everything I could think of. The second the vehicle it's 131 kPa it goes...
  8. Replies
    3
    Views
    1,935

    C7 Stingray 8L90E Converter WILL NOT LOCK

    I have a 2015 C7 Stingray with forged motor, LT4 blower, heads, cam all of the goodies. Triple disc converter and I cannot get this thing to lock to save my life! I can't get my line pressure above...
  9. Replies
    288
    Views
    306,764

    8L90E Issue

    Every time I get the parameters to where a car is over 380hp it gives me a "Data in Logic Error" If my stall speed gets above a certain amount or my HP goes above a certain amount. Any thoughts?
  10. Replies
    4
    Views
    2,463

    Your Base Airflow, add 5% to the areas affected...

    Your Base Airflow, add 5% to the areas affected then blend them into the upper zone slowly. Make sure the numbers always climb from right to left. If one is lower, interpolate it to where it is...
  11. Replies
    4
    Views
    1,519

    Have you tried switching upstream O2 sensors to...

    Have you tried switching upstream O2 sensors to see if it switches sides? It may have something to do with your O2 heaters. I've had 5th Gen Camaro's do something very similar for no reason. ...
  12. Replies
    4
    Views
    2,463

    First and foremost, get your fueling dialed in. ...

    First and foremost, get your fueling dialed in. Once you get your MAF recalibrated for your fueling it should tell you a better story. When fueling is off as much as it is the swing of your O2...
  13. Replies
    11
    Views
    3,066

    I just took a look at your tune. Your base...

    I just took a look at your tune. Your base running airflow is holy crap out of sorts IMO. Also your startup airflow can be added to to make things start a little easier. As someone that is...
  14. Replies
    11
    Views
    3,066

    Wouldn't he want to add to the base running...

    Wouldn't he want to add to the base running airflow and move the RPM up to roughly 800-850? Also he should add to startup airflow and move the under and over up to about 1.5 seconds.
  15. Replies
    3
    Views
    1,096

    Have you looked into the throttle follower? ...

    Have you looked into the throttle follower? Sometimes you have to add a few g/s to the throttle follower to keep it from hanging. Also, you may try to add a few percent here and there to the...
  16. I agree but this is just a minor takeoff. ...

    I agree but this is just a minor takeoff. Literally just letting out the clutch and gas at about 25-30% throttle it pulls Tq Mgt Adv at about 20*ish of timing to where the car is trying to...
  17. since the original post I've gone through and...

    since the original post I've gone through and tuned the VVE and tuned the MAF as well. Still does the same thing but only in 1st gear.
  18. Replies
    3
    Views
    1,335

    Have you gone through and datalogged your VE...

    Have you gone through and datalogged your VE tables? I'd say you are possibly having some transition somewhere that is causing the fueling to go wild. Possibly at a certain throttle percentage the...
  19. Replies
    5
    Views
    2,273

    I tend to get as much data I can on a single log....

    I tend to get as much data I can on a single log. If you can drive it around for 5 to 10 minutes and go through different throttle positions, you'll get the most data. My FIRST adjustment is always...
  20. Yes and it is Torque Management Advance is taking...

    Yes and it is Torque Management Advance is taking all of the timing out of it until about 3,000 rpm. Does it in 1st and 2nd gear mainly. Is that the virtual torque tables?
  21. LT1 to LT4 SuperCharger Swap. Need some help with a limiter Will pay for assistance!

    I have gotten the tune relatively dialed in with part throttle. It runs like a dream until about 45-50% throttle and starts to go into boost. Torque hits between 580 and 630 and hits some sort of...
  22. Is this corrected in the Virtual Torque Tables? ...

    Is this corrected in the Virtual Torque Tables? How do I set up a PID and histograms to set that up properly? Where do I source the torque to enter into those tables?
  23. 2016 Camaro SS Cammed. Some sort of timing limiter

    There is some sort of timing issue going on. Stage 3 cam, Hi-Ram Intake, E85, Long tubes exhaust and CAI. It's a stick car. When you go to take off it seems sluggish as heck sometimes. It will...
  24. Replies
    21
    Views
    13,633

    This worked! Thank you!

    This worked! Thank you!
  25. Replies
    21
    Views
    13,633

    Yeah I saw this thread and it is for the 2014's. ...

    Yeah I saw this thread and it is for the 2014's. They changed quite a bit between the two and it seems there really isn't any support out there for them.
Results 1 to 25 of 36
Page 1 of 2 1 2