Search:

Type: Posts; User: Christian GM

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Was one bad spark plug. small crack on insulator....

    Was one bad spark plug. small crack on insulator.
    strange that no missfire detected....
  2. added log and tune file (by Edelbrock) thank you

    added log and tune file (by Edelbrock)
    thank you
  3. 2012 Camaro LS3 eforce bad cruising feeling

    hello
    I've just installed a Eforce 1598 into a stock 2012 Camaro with MANUAL transmission
    if you keep the RPM above 2.000 it's all ok, nice to drive but the feeling is that not full power at WOT,...
  4. Replies
    2
    Views
    265

    2002 Duramax LB7 quick info

    hello guys,
    I'm not skilled on diesel, more on petrol...
    I see the tire size wizard is not there... how about properly adjust speedometer and tire size / transmission shift point?
    all manually?
    ...
  5. they're so bad?

    they're so bad?
  6. 2018 Challenger 6.4 with EFORCE Edelbrock

    hello guys
    Edelbrock has not released the tune for MY 2019
    I'm installing the EFORCE kit into a new Challenger A/T scat pack, 6.4 V8
    someone has to share the STOCK Edelbrock tune file for MY 2018...
  7. Replies
    0
    Views
    160

    2015 z06 lt4 a8 STOCK Corvette

    hello,

    application is Corvette VIN G5602310, odometer is KM 86.076 I did the full service to it one week ago, with new carbon rotors in the front, front & rear brake pads, engine and differential...
  8. Replies
    3
    Views
    399

    yes I did... like I did always but looks like on...

    yes I did... like I did always but looks like on this particular vehicle is not working.
    maybe I should read also TCM and FPCM?
  9. Replies
    3
    Views
    399

    hello nobody run into this issue? thank you

    hello
    nobody run into this issue?
    thank you
  10. Replies
    3
    Views
    399

    2010 Camaro V6 Speed Limiter LLT

    hello guys
    I have this car here.
    disabled at 270 km/h the speed limiter, selected source by calibration
    but put on the dyno and speed limiter cut of at 190 km/h
    any idea?
    thank you so much
  11. Replies
    3
    Views
    260

    vin change on 2019 Challenger

    hello guys
    I've a 2019 Challenger SRT with PCM unlocked by HPTuners service.
    I need to swap it on the car I have and obsiouly the VIN does not match
    how about changing the VIN?
    I'm not sure on...
  12. 2019 Jeep Renegade tire size - speedometer correction

    hello,
    On JEEP Renegade VIN KPJ39957 the tire size is stored into ABS module.
    I need to change value of circumference from 2.125 to 2.405
    But the system does not allow me to put the new value, did...
  13. no expereinces about it? tnx

    no expereinces about it?
    tnx
  14. 2018 RAM modification with OBD without modification is possible?

    hello guys
    this company claims they can do TUV (Germany) approved speed limiter modification and overall power increase on all RAM vehicles, including new 2019, with ODB only, no need of ECM...
  15. it's not there, this is why I'm asking here....

    it's not there, this is why I'm asking here.
    there is MY17, but I need MY18
    tnx
  16. Thanks a lot but I need us Camaro. It's not the...

    Thanks a lot but I need us Camaro.
    It's not the same
    Bye
  17. hello, nothing around? thank you!

    hello,
    nothing around?
    thank you!
  18. 2018 Camaro Auto, Performance Exhaust 6.200 V8 need stock file

    hello guys
    some one is so nice to share ASAP the STOCK file of 2018 (I already have 2017, need a 2018)
    I need the Camaro LT1, 8 speed auto, with performance exhaust
    I need a file with ECM and FPCM...
  19. yes they're. Chad Golen Engine Stage II

    yes they're. Chad Golen Engine Stage II
  20. Replies
    14
    Views
    914

    I have this style no screws at all, so I removed...

    I have this style
    no screws at all, so I removed the small screen, with a small socket and hammer I hit in the middle the FPR.
    this way I preloaded the spring, tested a couple of time, 5.0 BAR...
  21. I already know my intake manifold was not working...

    I already know my intake manifold was not working good.
    I found a machine shop to remove 0.040" from the china wall plane on the manifold, enlarged the bolt holes and now looks is everything ok...
  22. good to know! love forum and all precious info!!!

    good to know!
    love forum and all precious info!!!
  23. it's a damn intake manifold leak from the bottom....

    it's a damn intake manifold leak from the bottom.
    I pulled it out during launch
    will upload pictures and more info ASAP, hopefully late evening or tomorrow
    bye
  24. no sadly it's not ok. I opened another thread and...

    no sadly it's not ok. I opened another thread and will upload info ASAP, but I'm already on the right path to fix it.
    even if will not be EASY
  25. exactly, in 6 different point just to be sure the...

    exactly, in 6 different point just to be sure the reluctor was not out of round.
    I had a consistent reading.
    you're PERFECT under the specs Mike told me between 0.030 to MAX 0.040
    BTW, me too. I...
Results 1 to 25 of 203
Page 1 of 9 1 2 3 4