I have a ford flex and saw that it is supported under the new version.
But when I go to read the PCM it seems I need to select the ECM from a drop down? Which one can I use?
I tried different...
Type: Posts; User: BobDoLe
I have a ford flex and saw that it is supported under the new version.
But when I go to read the PCM it seems I need to select the ECM from a drop down? Which one can I use?
I tried different...
Any chance a 2014 Ford Flex will be supported? I've got one that is the regular NA v6 that seems to have very aggressive torque management.
I should also add that I tried dialing in the MAF a little more and that did not seem to have any effect either. Right now I'm throwing numbers I'm pulling off a Ouija board into a few things in the...
Thermal sounds likely. I did notice when forcing open loop at idle the bank2 O2 would go lean but wide band (sitting about an inch under it) was registering stoich.
So update... I did adjust VE...
OK just took the car for a spin. Cold start, drove out of my subvision and it was cruising fine at stoich (see 2 min 30 seconds in), but then a minute later I come to a stop and you can see 2 seconds...
I wasn't able to find what I was looking for with a search (not exactly sure what I'm chasing), so excuse the new thread if this has been discussed and resolved in another.
Summary: Car is...
i noticed your 2 posts are just a few hours apart - was the fix permanent?
is this P0106 thing found on a 99 fbody V8?
i had similar issues after heads/cam and i can see where p0121 can be...
On the (dyno dynamics) dyno, I had my stall locked up as commanded through hptuners and was logging slip. the stall manufacturer advised to avoid doing it often, but that it would hold.
However,...
just tried that also - no change.
loaded default imperial.cfg - still same problem.
removed and re-installed hptuners suite - still same problem.
loaded up an old scan from way back when (when...
regional settings - they're all at English (US) even in the advanced tab and everything.
here's a screenshot of the histogram.
i even tried using different configs and its still doing the same...
fuel solenoid failure? - dry shot with harris speed works interface = no fuel solenoid and computer controlled fueling while spraying.
fuel pressure? - fuel pressure safety switch (shuts off nitrous...
i'm having a problem where my VE-LTFT and STFT tables won't show MAP values (y-axis) past 15 (all dump onto 1st line).
can you take a look at this and tell me whats wrong with my config?
you...
i'm having a little slippage going uphill at part throttle with a 3600 stall performabuilt converter. i don't think the converter is really the problem as the manufacturer has indicated that it has a...
the performance mode option is simply an indicator of what sort of switch you have to activate the secondary shift tables (tow/haul, aka performance mode).
you need to leave it as is on the truck,...
this would be good information. i've seen the question posted a few times.
i've been searching and found nothing.
what changes are needed after a stall?
i've heard where people will usually hit...
would keeping it locked up all the way up to 80% throttle, keeping locked at 0% throttle be harsh on the stock converter?
decelerate is a bad choice of words - sorry about that - i guess what i want is engine braking as opposed to tcc unlocking and the rpm dropping to idle.
i guess if i experiment with locking the...
actually, my shift speeds are based off of something i found on your blog:
http://redhardsupra.blogspot.com/2005/08/road-racing-automatic.html
(thank you)
my concern now is when at 5000rpm and i...
any recommendations for shift modifications for canyon carving?
i setup the performance table (hooked up the button to switch from normal to performance) to get rid of part throttle shifting, but...
with a little help from jose (6speedterror) who has done this, i have also done this and have a few pictures...
basically, remove the plastic cover from the top pcm harness and loosen the middle...
i'd say removing torque management did my tranny in, but it was my 3-4 clutch that failed after a few wot 3-4 shifts on a 5 hour drive - stock torque management has no reduction in torque for 3-4...
here's the link you were referring to.. the individual who did the write-up advised that it was for 94-95 fbodies.
http://www.z28.com/forum/showthread.php?t=4764
has anyone successfully tried...
i knew the title would get your attention. someone please chime in here.
i was looking through some old logs and came about two that were a day apart. the thing that caught my attention is that the...
plugged into my friend's malibu maxx as well (with the recent 2.1.18) and it still is not supported.
My car is a 99 A4 SS with a lid and flowmaster catback.
Here are 2 scan logs, my tune and my scan config. I'm playing with a half/half mixture of 91/100 octane (I only drive the car on weekends)...