Search:

Type: Posts; User: vortech

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    63

    hybird maf/2bar setup

    This is probably been discussed before but I've been out of the loop on these for awhile now. This is a situation where I cannot run a larger maf pipe to get the flow down. I would like to run maf...
  2. Replies
    1
    Views
    100

    Meth injection to run E85 question

    I have a question in regards to Meth and E85. What is the preferred method to pull fuel to accomplish this, from the PE or MAF? Does it matter if it's a C7 Z06 with a top mount or if it's a C7 Z06...
  3. reduced engine power but not reduced engine power?

    Got a weird problem as of late, happened on 2 Camaro's 13 and 14. After tuning the reduced engine power came up on the DIC but no codes. Car doesn't go into limp mode it drives fine normal and wot...
  4. So I made the changes to MAF period but now it...

    So I made the changes to MAF period but now it seems the car is going a lot richer than the power enrichment commanded. 89811
  5. Here is the log with the added pids.89737

    Here is the log with the added pids.89737
  6. Thank You so much, I will add those and put it...

    Thank You so much, I will add those and put it back on the dyno tomorrow and report back.
  7. here is a pull up to 4700, then i shut it down. I...

    here is a pull up to 4700, then i shut it down. I was asking for .889707
  8. 2015 with Roush not going into enrichment at wot

    Trying to tune a 2015 Mustang with Roush blower and the car will not go89705 the enrichment commanded at wot? Any help would be greatly appreciated.
  9. Hi Bill, I fixed it. Had to change the resolution...

    Hi Bill, I fixed it. Had to change the resolution on my laptop from the recommended 1920 to 1366x768. That was it. The recommended window's setting messed it up.

    Thank You!
  10. 89161 Here it is-thank you!

    89161

    Here it is-thank you!
  11. Cannot see DTC codes in Editor uning Windows Pro and Dell E6440

    Hi, stupid issue that I'm hoping is an easy fix. Using a Dell E6440 with Windows 7 Pro. When I open up the editor and go to engine diagnostics and DTC's I cannot see the full error codes. Most of...
  12. Replies
    5
    Views
    286

    Thanks Higgs, thanks Ben. VE was 25% rich! I was...

    Thanks Higgs, thanks Ben. VE was 25% rich! I was shocked because this car is just bolt ons. So I dialed that in, MAF was already solid and now it idles at around 8-14 degrees. TPS went down from 7.8%...
  13. Replies
    5
    Views
    286

    Hi Higgs, I've tried everything from 7200 to 2500...

    Hi Higgs, I've tried everything from 7200 to 2500 and noticed no change by changing only that. The MAF is accurate and I will check on the VVE. Thanks Higgs.
  14. Replies
    5
    Views
    286

    No idle timing after Katech 103 C7 Z

    Car is C7 Z. Upgraded to a ported blower and a Katech 103. Nice increase in power but then I noticed something off. Idle timing is now only 3 degrees, Delivered engine torque is now in the negatives,...
  15. Send me a text and I'll send you what FIC sent...

    Send me a text and I'll send you what FIC sent me. 519-502-0915
  16. Replies
    17
    Views
    968

    I had the IAT table setup not to pull timing...

    I had the IAT table setup not to pull timing until it hit 171 degrees. I was only at 138. Strange thing is never pulled any retard in 5th in the summer months when it was 80+, its now in the 50's.
  17. Replies
    17
    Views
    968

    whats wierd is it never did it in the summer,...

    whats wierd is it never did it in the summer, just now in the cooler months and its making about 2-3 psi more.
  18. Replies
    17
    Views
    968

    Did you zero out the entire table? I would think...

    Did you zero out the entire table? I would think it would be IAT since IAT advance is showing the retard. I'm going to try to go back to the track this week and try again.
  19. Replies
    17
    Views
    968

    I'm not sure where you are seeing any knock...

    I'm not sure where you are seeing any knock retard? There is none reported on that run and the EQ ratio reported is .81 throughout the whole run.
  20. Replies
    17
    Views
    968

    Help with IAT advance pulling timing

    I ran my best the other day, a 9.84@137 but I noticed in 5th gear the car was pulling timing. I noticed in 5th the IAT advance was -7.7 degrees and MAT was only 138 and IAT 2 only 75. I had my tune...
  21. Confused as to what modifier is pulling out timing on a C7 Z06

    19 Z06, all the boltons with a 18% OD. Finally got the car working well. Then I noticed in 5th it was down on timing. MAT didn't go over 149 but it pulled out more timing than it should have based...
  22. C7 Z06, how to get them to shift he same in all modes?

    On a C7 Z06, how do you get the trans to shift the same in tour mode to track mode at wot. The shifting is much different in Tour mode vs Sport or Track mode.

    Thanks!
  23. Replies
    4
    Views
    389

    So it looks there is a table #2946 and it is not...

    So it looks there is a table #2946 and it is not on the 19's
  24. Replies
    4
    Views
    389

    C7 Z06 intercooler pump turn on temp?

    I saw somewhere somebody posted a C7 Z06 intercooler turn on temp table. For the life of me I cannot find that table. Is there one on the 19's and is there any benefit to turn the pump on sooner?
    ...
  25. Cannot turn on intercooler pump with scanner on LT4

    I cannot turn on the intercooler pump using the VCM controls on a 19 Z06. The tab is there but nothing happens.
Results 1 to 25 of 294
Page 1 of 12 1 2 3 4