Search:

Type: Posts; User: rpmextreme

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,369

    0C9 is the TACH. Byte 1 and Byte 2. both are...

    0C9 is the TACH. Byte 1 and Byte 2. both are multipliers. Byte 0 has something to do with idle or off idle.
  2. Replies
    1
    Views
    755

    Serial would be CAN based from the BCM. Hard...

    Serial would be CAN based from the BCM. Hard wire would be a direct wire to the TCM
  3. Any ETA on when that will be active again?

    Any ETA on when that will be active again?
  4. Our AC request module should with with the E38...

    Our AC request module should with with the E38 and E67. It may even work on the E40, just haven't tried it yet.

    The module just sends the AC request. You still need the 3 wire high side pressure...
  5. Replies
    0
    Views
    254

    Template Application question

    I like the new Template option.

    My question is why can't we apply DTC changes with the template or the compare function?

    We have a base tune that we apply with our products and it requires a...
  6. I don't think they ever offered the L86-8L90e...

    I don't think they ever offered the L86-8L90e with a manual T case.

    is there a vss in the T case now? if so can you move it to inbetween the trans and T case? that way it will read the same...
  7. I'm pretty sure you can.

    I'm pretty sure you can.
  8. http://www.rpmextreme.com/Category/70/Jeep-JK-LS-S...

    http://www.rpmextreme.com/Category/70/Jeep-JK-LS-Swaps.aspx
  9. We have not tested it on a E67.

    We have not tested it on a E67.
  10. Any updates on this. I have 2 MPVI2s that both...

    Any updates on this. I have 2 MPVI2s that both come up with Detect Protocol failed when trying to read a 05 GM 5.3 ECU 12589463. Both units have been fully updated and I ran Both the current Beta...
  11. Replies
    95
    Views
    21,670

    So that appears to work with the scanner. At...

    So that appears to work with the scanner. At this point is bluetooth only working with the scanner and not for the editor reading or writing?
  12. I have a module that will simulate the TCM and...

    I have a module that will simulate the TCM and output the speed message to the ECU at least on a E38.

    Currently I have it sending a 0MPH message for guys that need to get around Speed limiter and...
  13. Replies
    95
    Views
    21,670

    Something is up with these. hopefully HP Tuners...

    Something is up with these. hopefully HP Tuners will chime in with some details before this thing goes off the rails..
  14. Replies
    19
    Views
    3,425

    I have 3 brand new MPVI2s here. All show up as...

    I have 3 brand new MPVI2s here. All show up as WT12-A and non of them will communicate with the scanner or Editor via bluetooth. I think there is something wrong with these early units.

    I have...
  15. Replies
    95
    Views
    21,670

    I have 3 brand new MPVI2s here. All show up as...

    I have 3 brand new MPVI2s here. All show up as WT12-A and non of them will communicate with the scanner or Editor via bluetooth. I think there is something wrong with these early units.

    I have...
  16. Replies
    19
    Views
    3,425

    Any update on making the Bluetooth work? ...

    Any update on making the Bluetooth work?

    Has anyone been able to use the MPVI2 via bluetooth or is it just me?
  17. Replies
    19
    Views
    3,425

    Mine also says paired to WT12-A. It will work...

    Mine also says paired to WT12-A. It will work fine with the usb cable plugged in but will not connect to the scanner or editor ViA bluetooth even though is shows paired
  18. How do we set up our reseller side?

    How do we set up our reseller side?
  19. Yes you will need the GM AC pressure transducer...

    Yes you will need the GM AC pressure transducer wired up and working so the GM ECU can view the pressure properly. The AC request module will send the correct AC request signal to the ECU when...
  20. Replies
    6
    Views
    1,508

    That would be a parameter change in the TIPM

    That would be a parameter change in the TIPM
  21. Replies
    7
    Views
    1,887

    I have the same error but it's only on 1 or my 3...

    I have the same error but it's only on 1 or my 3 computers I updated. I will check to see if I'm in demo mode and report back.
  22. Replies
    10
    Views
    2,351

    All truck calibrations need a BCM to send the...

    All truck calibrations need a BCM to send the proper TUTD switch messages to the TCM. We have had good results with our EZcanbus module simulating these signals and making TUTD, Tow haul, cruise, AC...
  23. Replies
    6
    Views
    1,497

    Thanks guys. this is the info I was after. But...

    Thanks guys. this is the info I was after.

    But what if I'm using "maths" like LTFT + STFT and want to weed out any date that was -5 to 5.
    I can't seem to find a parameter to click on for Maths...
  24. Replies
    6
    Views
    1,497

    Filter setup based on value

    I was wanting to create a filter that would only show values above or below a certain value.

    Lets say I only wanted to show values in a fuel trim graph that were above 5. How could I set that up?...
  25. Replies
    18
    Views
    2,398

    Im getting a handle on it now. Getting the...

    Im getting a handle on it now. Getting the exhaust leak fixed and the VE table dialed in allow me to remove a lot of the AFM.
Results 1 to 25 of 123
Page 1 of 5 1 2 3 4