Search:

Type: Posts; User: Jace Jackson

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. chances are, your tuner just has the codes...

    chances are, your tuner just has the codes disabled but you're still running in a "reduced engine power" in the background
  2. Is the truck deleted

    Is the truck deleted
  3. Replies
    6
    Views
    550

    Contact support and they will add it. They added...

    Contact support and they will add it. They added all of those for me on the 3.0L Powerstroke
  4. Replies
    6
    Views
    550

    Parameter 14590 - Base Operating Mode will tell...

    Parameter 14590 - Base Operating Mode will tell you which of the Map # is in use.

    Parameter 14589 - Injection Config for EOM will tell you which Config # is in use.

    Parameter 14588 - Engine...
  5. Replies
    3
    Views
    1,183

    135780 General>Shift Type Config Set all of...

    135780
    General>Shift Type Config Set all of those to 0 just like my picture. This will disable 1st gear completely.
  6. Replies
    3
    Views
    780

    10R80 1st Gear Disable HELP

    Looking for some advice on disabling first gear. I've tried hundreds of times following the 4wd low table for disabling first gear with no luck at all. With first gear upshift OSS set to "zero" the...
  7. Thread: High idle

    by Jace Jackson
    Replies
    2
    Views
    916

    can you post a log? i can help you out.

    can you post a log? i can help you out.
  8. Replies
    15
    Views
    2,513

    LTFT's need to be within + or - 3%. i always try...

    LTFT's need to be within + or - 3%. i always try to get them within -1%
  9. Replies
    15
    Views
    2,513

    102257 Load this file up and get some more logs...

    102257
    Load this file up and get some more logs for me please. If easier you can email @ [email protected]
  10. Replies
    22
    Views
    15,194

    Go through the tune, and compare to your stock...

    Go through the tune, and compare to your stock tune. This will show you what has changed and what is different. It will give you a starting point to learn what needs changed.
  11. Replies
    15
    Views
    2,513

    You need to download vcm beta And use that

    You need to download vcm beta And use that
  12. Replies
    15
    Views
    2,513

    Get me some more logs and i can help you out....

    Get me some more logs and i can help you out. Need idle logs for a few minutes, cruising around and wot. Get me as much data as you can
  13. Replies
    15
    Views
    2,513

    102241 I have adjusted your VE Table and Maf...

    102241
    I have adjusted your VE Table and Maf based on your log. Your Long terms and short terms are all over the place adding up to 25% fuel. I smoothed out the VE table and increased it...
  14. Replies
    22
    Views
    15,194

    note: Vcm beta is required to open this file

    note: Vcm beta is required to open this file
  15. Replies
    22
    Views
    15,194

    102239 I have attached the E85 tune for you

    102239
    I have attached the E85 tune for you
  16. Replies
    13
    Views
    5,043

    102237102238 I have attached the tune and graph...

    102237102238
    I have attached the tune and graph setup for you
  17. Replies
    13
    Views
    5,043

    Nothing it was bone stock. But the stock VE table...

    Nothing it was bone stock. But the stock VE table on those trucks is horrible. This is set for 91 octane, truck drives amazing and shifts perfectly. I have updated the tune and will post tomorrow.
  18. Replies
    15
    Views
    2,513

    Can you post your file please?

    Can you post your file please?
  19. Download the latest vcm beta, shutter override...

    Download the latest vcm beta, shutter override should be on the latest beta
  20. Replies
    22
    Views
    15,194

    I'm willing to share my 2.7 e85 file with you if...

    I'm willing to share my 2.7 e85 file with you if you are looking for a big power increase. you MUST use full e85 for this tune. Reply back and let me know
  21. Replies
    22
    Views
    15,194

    all 2.7 engines use vacuum reference instead of...

    all 2.7 engines use vacuum reference instead of positive pressure for wastegate control
  22. Download the latest Beta from hp tuners. Then...

    Download the latest Beta from hp tuners. Then retry.
  23. Your VE and MAF table needs adjusted. On your...

    Your VE and MAF table needs adjusted. On your Log, the computer is trying to add 10% fuel in the upper rpm range.
  24. Replies
    13
    Views
    5,043

    102080 If your Truck is otherwise stock try this...

    102080
    If your Truck is otherwise stock try this file. This is a file i worked on for a while on a 2000 5.3 silverado. All LTFT's are within -1%. Truck drives great and pulls very good.
  25. Replies
    8
    Views
    1,901

    Does the truck run fine? Does it start and idle...

    Does the truck run fine? Does it start and idle fine? What do your LTFT's look like? VE table appears to be a little rough, also your High Octane spark table appears to be stock. Try increasing the...
Results 1 to 25 of 27
Page 1 of 2 1 2