Search:

Type: Posts; User: hachiroku

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. does that mean we can use HPTuners to overwrite...

    does that mean we can use HPTuners to overwrite another brand aka dimsports flash tune? over in the standard tuning forums one of the guys from HPTuners said he does not advise to do this as only a...
  2. it'll be referring to load. engine torque output...

    it'll be referring to load. engine torque output means nothing and is solely for us. if your load tables are out of whack your transmission will do funky things.
  3. Bill was able to respond to my question.

    Bill was able to respond to my question.
  4. Thanks Bill.

    Thanks Bill.
  5. Can HPTuners be used to overwrite and to return a flashed computer back to original

    I've read in some older posts that HPTuners can overwrite other ECU flashes if needed. Is this the case for all ECM's that HPTuners is available for? also, what would occur if the read file is...
  6. Thread: Shift RPM

    by hachiroku
    Replies
    0
    Views
    99

    Shift RPM

    Hey guys,
    Does configured redline have a direct effect on automatic transmission shift RPM? I have my redline at 7,500 but my shifts are occuring at around or a little over 6,800rpm.
  7. Can HPTuners be used to overwrite settings to return a flashed computer back to stock

    Can HPTuners be used to overwrite settings to return a DimSport or Renntech flash to stock assuming you have the factory parameters from a similar ECU? From what I've found through online archive of...
  8. Replies
    0
    Views
    94

    Assistance with Filtering

    Hello,
    Looking to filter out results where my MAF readings are less than 350 microsecond. I'm having issues with it actually working and am sure i'm using the expression incorrectly.

    tried and...
  9. possible to combine different logs into single view

    i have a log from this morning and this evening from the same tune. i want to combine the two so i can see averages, etc. would this be possible and if so how could i combine them?
  10. i haven't had any issues when modifying or not...

    i haven't had any issues when modifying or not modifying this map. currently mine is maxed out as i was troubleshooting another limp mode fault.

    nevermind...just saw this reply.
  11. any permanently logged faults will need an...

    any permanently logged faults will need an appropriate tool to clear. STAR/DAS or other.

    to disable the fault from appearing you'll need to disable the fault and not just the MIL checkbox.
  12. Replies
    0
    Views
    109

    Help with fuel trim swings

    hey guys. i seem to be at a loss in regards to fuel trim swings. it would seem that at times, hot engine or cold engine, trims across the board will swing positive or negative. if i data logged 4...
  13. P0106 Manifold Absolute Pressure/BARO Sensor Range/Performance

    Hello,
    Besides, 4028 Range High and 4029 Range Low, which other area's affect triggering of P0106? I have updated 11335 Maximum Intake Pressure but still am seeing P0106. I am naturally aspirated...
  14. lol...i thought about it when i was updating all...

    lol...i thought about it when i was updating all those monitor centric maps. was going to do that as a last resort, but luckily the updates i've done to all maps thus far have been successful.
  15. that did it! thank you! now i can fine tune my...

    that did it! thank you! now i can fine tune my Optimum Torque and Load to Torque maps.
  16. Optimum Torque 32900 and Torque to Load 32850 Issues

    Hey Guys,
    I seem to be having issues with modification of either of the two maps, Optimum Torque 32900 and Torque to Load 32850. If I touch either of these maps I am receiving a P061B (Internal...
  17. Replies
    3
    Views
    283

    my W211 E63 has "Torque Limit Request Limiting"...

    my W211 E63 has "Torque Limit Request Limiting" as disabled as part of the factory map. had to avoid using the injector multiplier entirely as any modification from me was causing a P0607.
  18. catalytic converters can handle any amount lean...

    catalytic converters can handle any amount lean value. when you run lean EGT's go down because there isn't any fuel to burn. what damages catalytic converters is excessive fuel and ignition of...
  19. Replies
    5
    Views
    557

    yep...will try a few more things. i had the same...

    yep...will try a few more things. i had the same issue with Eurodyne Maestro for my B6 Audi A4 with Motronic ECU. i believe i had to also update not only the check box for MIL but also but set for...
  20. Replies
    29
    Views
    5,284

    on my E63, throttle hits 100% with Accelerator...

    on my E63, throttle hits 100% with Accelerator Pedal D (SAE) and Throttle position hits 87.9% with its factory settings and factory map. if anybody is having issues i'd recommend simply copying over...
  21. Replies
    5
    Views
    557

    I've switched off MIL for all sensor 2 and...

    I've switched off MIL for all sensor 2 and catalyst items, but still receive a MIL
  22. Replies
    3
    Views
    283

    i'm on my 3rd day with the product and have the...

    i'm on my 3rd day with the product and have the same exact issues you describe.
  23. i have yet to try this or lean burn for the M156,...

    i have yet to try this or lean burn for the M156, but from what I've experienced with my Audi A4 B6, the Motronic ECU has this hard coded as a safeguard for that vehicle.
  24. Replies
    24
    Views
    13,564

    Sticky: agree...1/3rd of the first post no longer matches...

    agree...1/3rd of the first post no longer matches the latest version of VCM Editor 4.4.4
  25. Replies
    1
    Views
    152

    Sticky for BETA change log?

    Hello,
    Wanted to ask if there was a sticky for the beta software change log? I want to make sure that if there is no need for me to use the beta, meaning no features for me, that i won't use it.
    ...
Results 1 to 25 of 28
Page 1 of 2 1 2