Search:

Type: Posts; User: Kmoney

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    95

    It starts are rear wheel abs sensors to abs...

    It starts are rear wheel abs sensors to abs module then can bus to PCM and TCM.
  2. Replies
    3
    Views
    95

    Gonna need an abs module to get a speed sensor...

    Gonna need an abs module to get a speed sensor signal.
  3. I would look at turning them all off in the tune.

    I would look at turning them all off in the tune.
  4. Replies
    2
    Views
    230

    He is correct. That table is there to make...

    He is correct.


    That table is there to make the out computers in the car happy. It has to match the original config or you will get implausibility codes. Setting it to 5.7 won't effect...
  5. Replies
    9
    Views
    442

    Yes PCS table. I've been struggling with the lock...

    Yes PCS table. I've been struggling with the lock up. There is a file that 300c made that has the tables conversions that help with lockup times.
  6. Thread: Misfire P0300

    by Kmoney
    Replies
    17
    Views
    733

    borescope time.

    borescope time.
  7. Replies
    9
    Views
    442

    I lower {raised numbers} line pressure in the...

    I lower {raised numbers} line pressure in the lower areas to calm down my downshifts.
  8. Replies
    18
    Views
    779

    yes

    yes
  9. Replies
    18
    Views
    779

    PCM will work but you will need to program the...

    PCM will work but you will need to program the vin and make a few changes with hptuners. harness shouldn't be needed.
  10. Replies
    3
    Views
    210

    Probably gonna have to modify the tbody to close...

    Probably gonna have to modify the tbody to close it more while getting the tps voltage up a few more tenths. or you have a vacuum leak somewhere.
  11. Have you verified fluid level? Mak sure its not...

    Have you verified fluid level? Mak sure its not over filled. 2-1 down shift may be the issue. try moving that around a bit to see if it makes a difference. Im the same way. I dont drive it enough to...
  12. Replies
    4
    Views
    281

    Get rid of that thing.. they are terrible..

    Get rid of that thing.. they are terrible..
  13. lets see the tune?

    lets see the tune?
  14. What do you have for a fuel system? Tell us about...

    What do you have for a fuel system? Tell us about the build.
  15. Replies
    12
    Views
    704

    All that can be changed..

    All that can be changed..
  16. Replies
    2
    Views
    234

    I use the ford 80 pounders with my magnuson. they...

    I use the ford 80 pounders with my magnuson. they are taller so I use rail spacers.
  17. plugged cats....

    plugged cats....
  18. Replies
    2
    Views
    147

    Are you looking at the pedal percentage or the...

    Are you looking at the pedal percentage or the actual Tbody. Anything over 75 percent for Chrysler is considered WOT. But as always.... Post the tune and log..
  19. Replies
    12
    Views
    2,250

    I agree. I have a protorque 2800 I my car is...

    I agree. I have a protorque 2800 I my car is undriveable with the convertor unlocked in 1 and 2.
  20. Where is the tune? and are there codes?

    Where is the tune? and are there codes?
  21. Replies
    7
    Views
    412

    Most of those codes have the sensor ground in...

    Most of those codes have the sensor ground in common. I would start there. Then check 5 volt output from PCM. If you need schematics inbox me.
  22. Replies
    11
    Views
    676

    The only way I was able to prevent my car from...

    The only way I was able to prevent my car from doing this was to add to the idle speed run time. I changed from 176 to like 600 then 300.. It starts and flares and comes down slowly so that it doesnt...
  23. Replies
    2
    Views
    220

    What year is this car? Shouldn't you have your...

    What year is this car? Shouldn't you have your Pratio scaled for boost and the proper AFR?
  24. Coolant sensor is wired directly to pcm. Sent to...

    Coolant sensor is wired directly to pcm. Sent to cluster via Can bus. I highly doubt that you harmed the gauge as it has no way of voltage being applied to it.
  25. Replies
    20
    Views
    994

    when I build my motor, My right bank intake...

    when I build my motor, My right bank intake gasket got ripped under the supercharger. Was causing higher than commanded idle. But was also causing a right bank lean code.
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4