I don't know if I mentioned it, but I'm running ARH long tubes with their catted Y pipe, so I trust that at least their quality is good.
they're obviously smaller and shorter than the factory cats...
Type: Posts; User: Killavolt
I don't know if I mentioned it, but I'm running ARH long tubes with their catted Y pipe, so I trust that at least their quality is good.
they're obviously smaller and shorter than the factory cats...
My CEL is on currently after a trip about an hour away. I'll have to plug it into my truck and read them again for more info.
I believe right now it's only a P0134 code, and a P0420.....going by...
ARH explicitly states to NOT wrap their headers....
That being said, the Cat location for the Y pipe is actually WAY closer to the engine than the stock location where they both sat under the...
I'm on iOS, I'll look it up though.
It's not so much that I'm having a problem as it is that I've installed long tube headers lol.
Need to adjust that delay (as far I know) to make that light...
ok, so it's likely a calculation being done to get the values then.....I was mainly concerned if it was mislabeled or if it wouldn't actually work.
I'm kind of wondering if I can somehow log/chart...
So transport delay was enabled for my truck, but it's table says it's MAF vs RPM ......
so how is it getting a MAF value when Dodge doesn't use a MAF sensor?
Is this some kind of calculation?...
that's why I was asking if it is available on early Dodges because I wanted to talk to support about it. but I don't want to go asking them about why it isn't available, if it's something that just...
??˚
It isn't available for my 2005 Ram 2500 Hemi, so I'm just curious if it is actually available on other NGC3's or other Dodge vehicles/Hemis.
it's not unlikely, the tires are long discontinued I think, only one tire was replaced because that's where the truck took the hit. so they left the 3 others, and I'm not even sure where they got...
Long story short my truck is a rebuilt that I've had since about aug.
I have only just now noticed that when the people who repaired it replaced the right rear tire that it's just over 1/2"...
I don't think you're being a dick, I understand, I didn't mean to fill the forum with complaints, and that was never my intention. I made this specific post to mainly find out if others had the same...
serious? You need a subscription though, which is fine, but I can't seem to see how much it costs or what's needed
I also found out that the gear/tire wizard is not compatible with my truck, so...
Whatever happened with this? as of today Track Addict still doesn't work with bluetooth so I can't really use it too effectively.
so finally, after much bullish, support updated VCM Suite to a new beta that now reads my ECU/TCM properly and provides me with many more PIDs. There are still some missing but now the issue is that...
Both computers are in fact from a 2500, especially the one in my truck lol.
however, if that's the case that means I can keep trying computers from a 1500 too.
I'm determined to somehow make this...
So technically, support is still giving me the runaround because they're telling me it's an older OS and needs to be updated.
What about this one, the PCM I picked up from the wreckers.
...
Not sure how I find out what the OS ID number is?
This is what's in the infolog for the PCM that's currently in my truck
Protocol Info: SAE J2178, J1962: VPW
ECM: 10, VPW
VIN:...
HPT support is under the impression that someone with a WiTech can solve all my problems. They know it's a 2005.....
I don't even know who would have a DRB3, and not only are they expensive to...
Right I get that, but I don't think they even did anything.
When I went in there the first time I went in with the mindset that the ECU had previously been tuned, and I explained in detail what...
This is really getting nowhere.
At one point during my emails, basically mid conversation, I was greeted with an email "thanks for contacting support, please provide an infolog", so I think I was...
100% confident.
I'm really getting nowhere with this either, support is running around in circles and telling me shit they've already told me and they're treating me like I'm a god damn idiot at...
I also can't use a 2008 ECU on my 2005. anything 06+ is CANBUS, my truck isn't CAN.
Also, I can tune stuff yes, I have access to things in the Editor, but the problem is missing PIDs in Scanner. I...
I've got a second computer from the exact same truck, it has the same problem, there's nothing else on the OBD port because it's connected in my living room using a bench harness.
I sent Eric...
At this point I don't know if this is a problem with my computer (Two computers) or my MPVI2 or something.
When I try to connect to my truck (2005 Ram 2500 5.7L) to do a read I have to manually...