Search:

Type: Posts; User: 3.6P

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    352

    supercharger and manual swap idle issue

    hi
    supercharged ,cammed and manual swapped crown vic
    the car had only one issue
    the car always stall when engaging clutch and needs to press pedal for couple seconds after start up to idle
    i...
  2. Replies
    4
    Views
    755

    return it back to stock values dont mess with...

    return it back to stock values
    dont mess with throttle angle
    if you open key on and press pedal with out starting the car you can see throttle fully open at 75-76% TPS
    if you want to increase...
  3. Replies
    2
    Views
    1,099

    thanks i have tried disable rpm error didn't...

    thanks
    i have tried disable rpm error didn't work
    still command 5XX rpm at drive

    there is no knock , yeah timing lower than the tune because the log before i increased timing
    on 1 to 2 shift...
  4. Replies
    7
    Views
    1,861

    post your tune and log for the car explain more...

    post your tune and log for the car
    explain more idle hang or stall ?
  5. Replies
    2
    Views
    1,099

    big cam idle issue

    hi
    crown victroia stock engine with bolt ons and stage 5 comp cams (XE278AH)
    tuning the car was fine for WOT and CRUSING but idle bring me headache
    at neutral or park fine with increasing rpm...
  6. Replies
    0
    Views
    510

    calc map max for cam swap

    hi guys,

    4.6 2v with big profile cam
    the car at idle barley have vacuum
    PCM throws p0106 * map performance*
    i know rising Calc Map max will solve this problem
    but what's the equation for...
  7. Replies
    4
    Views
    1,521

    thank you decipha Engine > Torque Model >...

    thank you decipha

    Engine > Torque Model > there are 2 tables Engine torque and Inverse
    if i increase value at idle cell from Inverse Table will make idle spark jump

    if can you make...
  8. Replies
    4
    Views
    1,521

    I've tried before with idle tables without no...

    I've tried before with idle tables without no success
    if lean it out to 19:1 at idle start to chop and timing jumps from 15-25 around that but i dont like exhaust smell
    if you have any suggestion i...
  9. Replies
    4
    Views
    1,521

    4.6 cammed choppy idle

    hi guys,
    4.6 2v bolt ons and cammed crown vic
    mid cam : XE268H
    Intake Duration at .050 Inch Lift:230
    Exhaust Duration at .050 Inch Lift:236
    Intake Valve Lift:0.5
    Exhaust Valve Lift:0.5
    Lobe...
  10. Thread: V6 charger

    by 3.6P
    Replies
    2
    Views
    898

    we need your stock tune did you have cats ? ...

    we need your stock tune
    did you have cats ?
    pops will destroy your cat's
  11. Replies
    2
    Views
    1,008

    can't write X7F Negative Response Code

    hi
    2010 charger
    i'm getting this error Controller Locker : Undefined X7F Negative Response Code
    while writing 30 seconds later of writing has stopped and error shows up (TIME OUT) after that i...
  12. Replies
    71
    Views
    24,790

    nope, if you wants the most hp of your engine...

    nope, if you wants the most hp of your engine shift around 6000 rpm if the car have few mod
    bolt ons shift around 6100
    4.6 screams loud at high rpms its normal that engine have a nice tone
    if...
  13. Replies
    71
    Views
    24,790

    110845 rev limit and trans tune what is your...

    110845
    rev limit and trans tune
    what is your mods and fuel
  14. Replies
    4
    Views
    1,039

    Thanks decipha for the information so, i...

    Thanks decipha for the information
    so, i changed ATT table only
    normal and high load still 45 psi
    is that ok .?:rolleyes:
    110830
  15. Replies
    4
    Views
    1,039

    2008 crown vic 4.6 2v

    2008 crown vic 4.6 2v
  16. Replies
    4
    Views
    1,039

    fixed returnless fuel pressure Tuning

    hi guys,
    Fixed fuel pressure set to 45 psi
    for desired fuel pump pressure tabless :

    -Ambient air temperature AAT
    110819
    -High load
    110820
    -Normal
    110821
  17. Thread: 4.6L 2V tuning

    by 3.6P
    Replies
    8
    Views
    8,958

    post a thread

    post a thread
  18. Thread: 4.6L 2V tuning

    by 3.6P
    Replies
    8
    Views
    8,958

    At Wot u will see Tps around 76% its fully open u...

    At Wot u will see Tps around 76% its fully open u can check it
    remove intake turn ignition on
    press pedal fully and check it

    update : 2017 post :rolleyes:
  19. Thread: closed loop delay

    by 3.6P
    Replies
    2
    Views
    800

    thanks any suggestions by tuning

    thanks
    any suggestions by tuning
  20. Thread: closed loop delay

    by 3.6P
    Replies
    2
    Views
    800

    closed loop delay

    hi guys
    i have bad experience with new oem BOSCH o2 sensors they always take about 2 minute to warms up and makes fuel trims stuck full lean with longtubes headers
    i never had any problems with old...
  21. Replies
    20
    Views
    8,505

    it happen sometime often with me close vcm suite...

    it happen sometime often with me
    close vcm suite and unplug mpvi2
    plug it again and resync it should work if you car already licensed
  22. Thread: 2001 crown vic

    by 3.6P
    Replies
    5
    Views
    1,580

    any future support for this platform? 1998-2004...

    any future support for this platform? 1998-2004 vic's
  23. Replies
    2
    Views
    5,605

    u can change gear ratio very easy dont worry but...

    u can change gear ratio very easy dont worry but needs a tune
  24. Replies
    2
    Views
    5,605

    u can use hptuners by vcm suite some cars dont...

    u can use hptuners by vcm suite
    some cars dont need credits and you can change gear or tire ratio by vcm scanner like dodge
    but crown vic's need a tune by vcm suite which need credits
    stock...
  25. Thread: WOT timing issue

    by 3.6P
    Replies
    4
    Views
    1,287

    i did experiment guys i unplugged IAT sensor...

    i did experiment guys
    i unplugged IAT sensor Immediately check engine light came on
    tried the same things on CAM phaser's nothing happen no Check engine light so, its bad PCM or what
    i started...
Results 1 to 25 of 40
Page 1 of 2 1 2