Search:

Type: Posts; User: FstdodgeKY

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    23

    2011 5.7 cam swap.

    Need some guidance on a cam swap for a buddy. He swapped the cam on a 2011 5.7 and looking to install a comp cam lst269hr14. I haven't dug my feet into tuning a camshaft yet so just curious on what...
  2. Replies
    1
    Views
    38

    Cant say ive ever worked on one of these cars,...

    Cant say ive ever worked on one of these cars, but... in my experience ive learned that when something like this happens its normally traced back to something simple or something you have...
  3. Replies
    2
    Views
    121

    A permanent code you cannot clear. It will only...

    A permanent code you cannot clear. It will only clear after the required fix has been done.


    Permanent Diagnostic Trouble Codes (DTCs)
    A Permanent Diagnostic...
  4. Thread: trans flair

    by FstdodgeKY
    Replies
    1
    Views
    113

    Signs of the clutches going out????? Just a...

    Signs of the clutches going out????? Just a thought... Over Temp on trans?? Monitor shift pressures and input shaft speed to see if its the clutches slipping..
  5. That's a lot of information, but as i read it a...

    That's a lot of information, but as i read it a few more times i believe this is very beneficial in learning how the ZF8 transmission works. I haven't got to the tuning side of the trans yet but...
  6. Get anywhere??? just curious.

    Get anywhere??? just curious.
  7. The settings look to be right. This is all...

    The settings look to be right. This is all controlled by ect sensor. you might try changing the #s to the extreme opposite just to see if that gets you anywhere.
  8. My best guess would be finding the wiring...

    My best guess would be finding the wiring schematic for both vehicles and make sure that's correct. I dont see simple swapping a clutch fan out for e fan would work. Also sounds like you only...
  9. was this a factory swap part??? Or is it...

    was this a factory swap part??? Or is it aftermarket?? The only way to control the fan with the pcm is if its supported by the pcm and connected correctly. If this is a aftermarket setup most...
  10. Replies
    1
    Views
    97

    make sure you are in advanced mode.

    make sure you are in advanced mode.
  11. Replies
    17
    Views
    546

    I did scope the clyinder and didnt find any...

    I did scope the clyinder and didnt find any evidence of bad ringlands and everything looked good and surprisingly clean as well. Guess I'll look at the tune and see what I can do there.
  12. Replies
    17
    Views
    546

    I'll have to get me one. any recommendations for...

    I'll have to get me one. any recommendations for borescope
  13. Replies
    17
    Views
    546

    Thanks conan. I am logging sft+lft. And I...

    Thanks conan. I am logging sft+lft. And I hitting around 8 # of boost. I'll look at adding some fuel up top and see if it helps.
  14. Replies
    17
    Views
    546

    9438094381here is a log I did after making a few...

    9438094381here is a log I did after making a few changes to the car. I did notice a few unusuall things. In a few spots the o2 sensors seem to be reading a different ends of the spectrum and also...
  15. Replies
    17
    Views
    546

    Didnt think about the injectors but i did have...

    Didnt think about the injectors but i did have two on both banks with bad o rings could be that as well. I'm hoping its not the ring-lands but if it is 426 here we come!!
  16. Replies
    17
    Views
    546

    Misfire P0300

    So here lately ive been getting a misfire code p0300. Plugs look good gaped at.026. Car has been running strong and still does but the code only pops up after a WOT pull, dosent happen all the...
  17. I'll try to help with what i can but i'm not...

    I'll try to help with what i can but i'm not exactly sure. Just how i think it does.

    MDS Multiple Cylinder Deactivation- Its is what is says it is, shuts downs certain cylinders to save on...
  18. Replies
    3
    Views
    240

    I just did a resync and I'll see if that helps me.

    I just did a resync and I'll see if that helps me.
  19. Replies
    3
    Views
    240

    Haha that's was the first problem. I have done...

    Haha that's was the first problem. I have done this now. my problem now says protocalled failed when I try to read the pcm. Also when I tried the scanner it said that it may need to be approved by...
  20. Replies
    3
    Views
    240

    New Laptop not working with interface

    Should be simple I thought, Got new laptop, downloaded and updated all software, can use software but CANNOT "see" interface. I believe I need to resync the the mvpi2?? I tried and all it says...
  21. as spoolboy said WOT and PT spark are what you...

    as spoolboy said WOT and PT spark are what you will get in those modes. to add to this The only way for them to change would be spark knock,cold and hot deadband as well as a few others i cant think...
  22. Replies
    11
    Views
    352

    Is the stock scat pack PCM capable of reading...

    Is the stock scat pack PCM capable of reading additional WB? how close in similarities are the hellcat PCM and what pack PCM?? One wouldn't think it be just as easy to swap harnesses and pcm?? ...
  23. Replies
    7
    Views
    372

    Is this something that might be available in the...

    Is this something that might be available in the near future?? Or should I not hold my breath.... I can only speak for myself when I say even the limited use of factory transbrake would be a great...
  24. Replies
    11
    Views
    352

    curious as well

    curious as well
  25. Replies
    7
    Views
    372

    So im going to bring this thread back from the...

    So im going to bring this thread back from the dead just to see if anything has changed. I have done some homework on this and so it seems that the 1320 challengers are running the same trans...
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4