Thank you,
That's exactly what I was looking for. Didn't find it during my searching but was hoping it was there somewhere.
John
Type: Posts; User: GMjohn
Thank you,
That's exactly what I was looking for. Didn't find it during my searching but was hoping it was there somewhere.
John
2004 6.0L with 4L80E
Has trans perf option set to serial originally as the PCM gets it's request from the BCM.
One of the options is 'Switch' as a selected source. I have searced and have not...
If I remember correctly if you unplug the FPCM you have to jumper the GMLAN wires to keep the communications bus in tact. May cause other system issues if you leave the FPCM disconnected.
When...
Resolved.
Thanks Bill.
John
Quick question-
I had 1 upgrade credit stored in my interface. When I upgraded to full year/model the 1 upgrade credit was not applied. I ended up using the full 6 credits . The interface no...
That's what I am looking for. Thank you. It appears to be limited to an 8-bit number. Things make a little more sense now.
Thanks,
John-
Bill,
Thanks for the reply. I think I am just going to turn the code off for now.
I may experiment at a later date if I feel the need.
John
LB7- Simple mods (Intake exhaust) now setting an overboost code.
Wastegate working good, it's easy enough to turn off the code but but I see a parameter for overboost max error. I don't see a...
Just a quick question- Downloaded my first 08 K2 6 (LMM Allison)
Under speedo there is two final drive ratios listed-
ratio 3.73(original gears)
Trans 4.10 ??
Vss tire revs
oops, didn't look at all the dates-:doh:
John-
Grab a test light and check pin 16. Should be batt voltage, that's what powers up most adapters. If not start checking fuses.
Refering to aldl pins-
\ ---------- /
\ ---------16/
John
Oh yah,
And what CRASHNBURN said-:banghead:
John
I am referring to any time out issues during a read of the TCM 01-05.
I had hoped that if new development was done that issue may have been addressed? I can see I am not the only one with issues....
Does the new version address any Duramax TCM issues??
Just curious with the new Duramax models available.
John
Tried again with the 2.8 usb 1.1 machine in High speed.
Failed- again in the TCM. This time I consistantly received the error-
Invalid byte count in block transfer.
I did however manage to...
Keith,
That's what I was looking for.
Thank you
John
Thanks,
I am mainly curious if an 04.5 LLY is considered an 05 or an 04.
I haven't checked but I think it runs the same OS as an 05 LLY.
From my standpoint an LLY mid year is an 04. Just...
Will an 04 year/model license do an o4 vin 1 and an o4 vin 2?
Both were available .
John
No difference with the USB 2.0
I saw some previous post's with overrun issues, hoped this would do it.
ECM dumps fine it's the TCM I have issue with.
If it helps anything here is my info...
I have, oddly enough it fails in a different location. Actually reads a little bit more.
First attempt with a 2.8 ghz P-4 laptop. USB 1.1
Going to try my other laptop today.
1.7 ghz P-M USB...
I am having this issue also. 04 k2 LB7.
I fail reading at the same location using .18 HPT software.
Actually I fail consistantly at 64C00, Every time on the trans controller.
For what I...
Reaching a bit here, Interface should light up just plugged into the usb port.
See if your interface powers up from the USB port when your laptop is connected to wall power.
It is a USB...
06 YY
Try fuse Rear Fog/ALDL(10A)
May be labled Top Sw or Top Switch
GMJohn
Just a quick update.
Second read- Good. Shows both PCM O/S and TCM O/S
Able to edit as planned. Burned without issue (~6 minutes)
All is well
Thanks
John
Thanks, I will give it a try. I'm still learning the GUI. Didn't figure out untill later that read is disabled with a file open. After the write failed I noticed read was disabled and was a little...