Hi All,
I installed a built 6L80E into a 2008 Pontiac G8. The car wasn't running for 5 years, so idk if that could be causing this, but just want to put it out there.
Whenever I drive and log a...
Type: Posts; User: TXjeepTJ
Hi All,
I installed a built 6L80E into a 2008 Pontiac G8. The car wasn't running for 5 years, so idk if that could be causing this, but just want to put it out there.
Whenever I drive and log a...
Hi,
I noticed on my scans that I had 'Control Module Voltage (SAE)' being logged, and the value for it was all over the place. 17volts, 19 volts, one scan showed 1 volt. I started to freak out.
...
Looks like adjust my timing DID do the trick. It shoots up to 3k rpm now, hits a wall - but I'm pretty sure that it is turbo lag now. Drives ways better
Will do
I should have added in the 1st post - it is a boost referenced return style system on it. Damn, had no idea offset was setup for returnless. I'll get that fixed ASAP!!! I'm trying to...
Hi all,
Mod list:
1970 Chevelle
Vehicle weight approx. 3,700lb
3.31 gears
Stock 2005 4L80E
Circle D 05D-12-05-2D-P 4L80 PRO SERIES SINGLE 258MM 2D-P 3700RPM
All stock LQ4 besides Texas Speed...
Sorry for the late response.. The LS3 Manual ECU cannot run an Auto, and an ECU from an auto will run a T56 conversion, but you will have issues such as speedometer. It's best to grab an ECU from a...
Thanks, Keith. I even read through the help files.. not sure how I missed that. Sorry for taking up your time!
I'm wondering if it is possible to filter out the area below outline in blue. It's the point where Commanded EQ goes from 1.00 to PE mode 0.75. The data in my scan is getting skewed (showing lean)...
My friend has a supercharged LS2 I just swapped into his 1972 Camaro. It came out of his 2006 GTO, which had been professionally tuned, so we yanked that PCM from the GTO and used it for the swap.
...
Been on and off the phone for the past few hours trying to figure this out.
I have a 2008 Corvette LS3 ECU E38 that was made for a manual transmission (T56).
I have a car that is expected to...
Thanks for the reply!
So does it matter what OS the transmission controller has or the service number? I'm seeing differing opinions. Some people say the E38 has to have a "matching" T42, others...
I attached the base tune to this post, that I just downloaded from the PCM.
Do I simply do a segment swap with a 2008 Silverado 5.3L? I can't really find anywhere in the tune where it says the...
I solved this issue, it was 100% my fault.
I'm guessing I deleted the PID, and when I re-added it, I did not do it the correct way. I had to transform the INPUT 1 input, now it is working
Found the issue, 100% my fault
I guess I accidentally deleted the PID from my channel list. When I re-added it, I didn't follow the correct procedure. Since I'm using the analog input, I had to...
Did you ever figure this out? I am having the same issue
Anyone ever fix this issue? I made sure my software was up to date, still getting the disappearing wideband
Same issue here.. It was working literally last week, now all of a sudden it disappears when I hit record
If I log interface input 1, I get the correct corresponding voltage - but the EQ Ratio...
I disabled it, but am still having issues tuning the VE table. It looks like if the IAT goes from 100 degrees to 110, it pulls a lot of fuel. When the car reaches operating temp, my idle AFR is 13.3,...
I tuned my friends car and switched it to 1bar SD OS, which I noticed it disabled the cylinder charge temperature
I've been having issues tuning my car, which has a 2bar SD OS, and I noticed that...
About to quit tuning all together, I CANNOT tune the VE table for the life of me. I have been trying to tune it on/off for the past 3 years..
Anyways, I just attempted to tune VE again.. I made...
I did a 80E segment swap, noticed the TCC wasn't locking up...
I read from a person that the donor file they used was "corrupt" which caused the TCC to not lock up. So I downloaded a different...
Hey I had the same issue, turned out to be System>General>PRNDL Equiped ---- I had it set to "NONE" and it needed to be set to "PRNDL"!!!!!!
Having an issue with the car dying when putting it into gear, and also when I blip the throttle from a stand still.
I was idling in Park, and since the car was running good, I copied/pasted those...
I found a 2002 Camaro F-body tune on the repository that has the same OS as the new PCM we plan on using.
Could I just segment swap over everything from this Camaro PCM? I find that the PCM I...
My friend bought an LS2 crate motor that came out of a 2000 Camaro SS, which was professionally dyno tuned. I have the tune from that PCM and I have the license for this PCM
My friend installed it...