Search:

Type: Posts; User: Homer

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    211

    What do you have your WOT FA set to at the high...

    What do you have your WOT FA set to at the high end? Your commanded fueling goes from 0.862 to 0.923 just before 7000rpm and just before throttle torque source switches.
  2. If you are not running high flow cats then it...

    If you are not running high flow cats then it will be difficult to get the monitors to complete. I have heard of guys running these

    http://www.bigdaddiesgarage.com/

    but I don't personally know...
  3. Replies
    9
    Views
    211

    So setting fuel cutoff higher than max RPM still...

    So setting fuel cutoff higher than max RPM still gives you a lean condition near max RPM?

    94950
  4. Replies
    3
    Views
    125

    Have a look here, I think the 3bar caliber...

    Have a look here, I think the 3bar caliber transfer functions are also given...post 13.
    https://forum.hptuners.com/showthread.php?78531-2019-Jeep-JK-ProCharger-HELP-NEEDED-PLEASE!
  5. Replies
    3
    Views
    125

    Double post.

    Double post.
  6. Replies
    14
    Views
    325

    There have been quite a few folks on the CT forum...

    There have been quite a few folks on the CT forum where the fobs stopped working after a dead battery. There was a recall on the 2011 models (not 100% on the year) which had to do with the WIN...
  7. Replies
    14
    Views
    325

    Nope can't do VIN.

    Nope can't do VIN.
  8. Replies
    14
    Views
    325

    There were a couple of guys on the...

    There were a couple of guys on the challenger/charger forums recently with a similar issue. One was due to interference coming from a wireless camera, another one was dead fob batteries, and the...
  9. Thread: Misfire P0300

    by Homer
    Replies
    17
    Views
    546

    I bought one of these which has a built in LED...

    I bought one of these which has a built in LED light ring and plugs into my phone. Images are good enough to determine condition of bore and piston....
  10. Replies
    1
    Views
    137

    The throttle blade will never show 100%. ...

    The throttle blade will never show 100%. Instead, log throttle voltage. As for your throttle surge, that is probably due to the fact that most your air tables are stock. The fix seems to be to...
  11. Replies
    2
    Views
    185

    The tazer (modifies the head unit not PCM)...

    The tazer (modifies the head unit not PCM) version can be programmed to an aux button on the steering wheel. Really nifty to have. I doubt HP tuners can enable it as it modifies the PCM.
  12. Thread: Misfire P0300

    by Homer
    Replies
    17
    Views
    546

    Could possibly be the land rings if Whipple #9...

    Could possibly be the land rings if Whipple #9 means 9 psi boost on stock 392 internals. :shrug:
  13. Thread: Misfire P0300

    by Homer
    Replies
    17
    Views
    546

    Have you tried swapping the injectors to see if...

    Have you tried swapping the injectors to see if the misfiring cylinders change?
  14. Replies
    2
    Views
    216

    Have you downloaded the latest beta?...

    Have you downloaded the latest beta?
    https://files.hptuners.com/VCM%20Suite/VCM%20Suite%20(Beta).msi

    Also you need an internet connection for VCM to access JTEC controllers.

    If you tried all...
  15. Replies
    2
    Views
    177

    Have you tried these tables? 94178

    Have you tried these tables?
    94178
  16. Replies
    62
    Views
    17,157

    I am not 100% sure but I think the PCM waits for...

    I am not 100% sure but I think the PCM waits for the VSS to be greater than the limit set for idle (normally VSS<3 MPH is considered idle). On the GPEC2A controllers I think it gets the VSS signal...
  17. Replies
    4
    Views
    228

    2009 chargers run the NGC4 PCM which is not that...

    2009 chargers run the NGC4 PCM which is not that old. Anyone that can tune GPEC equipped vehicle should be able tune a 2009 charger.
  18. Replies
    2
    Views
    239

    How about the offset tables?

    How about the offset tables?
  19. Replies
    15
    Views
    499

    One advantage I could think of would be the VVT...

    One advantage I could think of would be the VVT values would not have to be offset. As I state before, the 5.7 PCM shows full cam advance with and exhaust angle of 125 deg where as a 6.4 PCM sees it...
  20. Replies
    15
    Views
    499

    I thought the witech stuff would somehow not...

    I thought the witech stuff would somehow not allow it or the 5.7 BCM would have issues with the 6.4 PCM. I mean, if you look at the tune details in HP tuners it lists the vehicle info which I...
  21. Replies
    15
    Views
    499

    So a 6.4 PCM running 6.4 OS can be programmed...

    So a 6.4 PCM running 6.4 OS can be programmed with a 5.7 vin?
  22. That is because you are in the basic view. ...

    That is because you are in the basic view.
    93936

    This is what advanced view looks like.
    93937
  23. Replies
    3
    Views
    1,137

    I would not load the tune as is but copy the...

    I would not load the tune as is but copy the changes over to your stock tune. I would change sensed MAP threshold to 0.9kPa and disable baro fine learn. Power enrichment in the tune posted is not...
  24. You will want to enable sensed MAP and disable...

    You will want to enable sensed MAP and disable baro learn. Some other changes are listed in the link below....
  25. Replies
    3
    Views
    955

    LoL, tell that to the Tuning School. In their...

    LoL, tell that to the Tuning School. In their general dodge tuning book they say +2018 only needs the security bypass cable.
Results 1 to 25 of 475
Page 1 of 19 1 2 3 4