Search:

Type: Posts; User: ns158sl

Page 1 of 18 1 2 3 4

Search: Search took 0.00 seconds; generated 56 minute(s) ago.

  1. Replies
    501
    Views
    52,798

    Yeah Smokeshow. Then I'd try Dave Steck or Howard...

    Yeah Smokeshow. Then I'd try Dave Steck or Howard at Redline, maybe they have a work around being im sure they've seen it before.
  2. Replies
    501
    Views
    52,798

    Has anyone reached out to Dave, Jake, or Howard?

    Has anyone reached out to Dave, Jake, or Howard?
  3. Replies
    9
    Views
    290

    If the Cal is way out of whack, usually trims are...

    If the Cal is way out of whack, usually trims are way too slow to react and throw you off. Yeah you can literally comb through the log by hand but for someone new that is going to copy and paste, I'd...
  4. Replies
    9
    Views
    290

    I guess it's been awhile since I've done a gen 3...

    I guess it's been awhile since I've done a gen 3 on the street. Sounds good.
  5. Replies
    9
    Views
    290

    Filter out decel and quick transitions. You can...

    Filter out decel and quick transitions. You can always remove filters after you have a base to see what the ECM thinks it wants.
  6. Replies
    9
    Views
    290

    Put it back into closed loop and adjust the VE...

    Put it back into closed loop and adjust the VE with fuel trims. If the trims are off by 5-6 or more then multiply by full. Once you get it tighter, then multiply by half. Use plenty of filters on...
  7. Well. First is to quit picking a fight with a guy...

    Well. First is to quit picking a fight with a guy trying to help, even though Ed can be a little "straight forward", lol. I can't remember your set-up but is it more or less a Stock longblock with a...
  8. Replies
    10
    Views
    490

    So I have adjusted the EVAP tables quite a bit...

    So I have adjusted the EVAP tables quite a bit now and it seems to be getting way better data. I guess at this point Id like to see a log of a stock vehicle and compare purge DC vs tank pressure...
  9. Replies
    37
    Views
    704

    Did you write entire after you turned VATS off?...

    Did you write entire after you turned VATS off? Post a log.
  10. Replies
    10
    Views
    490

    So thats the part I don't follow. I mean this is...

    So thats the part I don't follow. I mean this is steady state loading with good RPM and I can hear the engine lug down. Go back and look at the logs and yep, InjPW comes up, EVAP goes to a hundred,...
  11. Replies
    10
    Views
    490

    So reducing the duty cycle under that low flow...

    So reducing the duty cycle under that low flow table made all the difference for my startup and idle issues.

    Still havn't figured out the around 50 KPA where it gets a huge rich spike and throws...
  12. Replies
    10
    Views
    490

    Nope, honestly ive been staring at the logs vs...

    Nope, honestly ive been staring at the logs vs tune and stumbled across the purge PWM, table 25012, ive reduced it to match stock idle airflow vs PWM to current engine. Ill try that tomorrow. Ive yet...
  13. Replies
    2
    Views
    154

    Wiring or fuel injectors

    Wiring or fuel injectors
  14. It is in Open Loop at the beginning. Maybe i am...

    It is in Open Loop at the beginning. Maybe i am blind, but i dont see why. Pull codes and see if anything pops up. Being it is stock, if fuel pressure is good (which should be verified), it should...
  15. Replies
    10
    Views
    490

    Well I honestly think it was the gas cap not...

    Well I honestly think it was the gas cap not vacuum breaking. It didnt do the stall during warm up after start. It still dies when I pull the cap after the car is running. Rightfully so being it goes...
  16. Replies
    10
    Views
    249

    Well with a tune and a log maybe someone can give...

    Well with a tune and a log maybe someone can give ya some tips on how to get it to a "base" tune with probably one to two flashes. After that your going to have to dial it in like you would with...
  17. Replies
    4
    Views
    192

    I wouldnt change everything from a 6.0 to that...

    I wouldnt change everything from a 6.0 to that file. I think the most I would do is swap the cyl volume and transient fuel tables (if available). Its going to have to be "tuned" being it is an...
  18. Replies
    8
    Views
    302

    Need to set the maf faults to error on first....

    Need to set the maf faults to error on first. Also seems like e38s like to have the maf fail freq something other than 0, so maybe 4 hz and 6 hz. Lower your idle timing 3-5 degrees. Why did you...
  19. Replies
    8
    Views
    302

    Did you have a new tune to post with the updates...

    Did you have a new tune to post with the updates Ed suggested to change? Otherwise we are just guessing on what was changed. If you do have a an updated tune, post a log with timing.
  20. Replies
    10
    Views
    490

    Well it is commanding 100 percent almost all the...

    Well it is commanding 100 percent almost all the time. I dug around in alldata for more of an explanation on when it purges vs tank pressure. I've replaced that purge valve yesterday and then cycled...
  21. Replies
    10
    Views
    490

    Ok I have something related to EVAP going on. I...

    Ok I have something related to EVAP going on. I have steady state tuning this thing and it isnt going as well as it should, lol. I am reviewing the log and just randoming you can see tank pressure...
  22. Replies
    10
    Views
    490

    Stall while removing gas cap

    So I have been fighting an issue after say a drive, if you pull the gas cap loose while the engine is still idling, itll pretty much flood itself and die. I can get a log of that shortly. I do have a...
  23. Replies
    15
    Views
    667

    Yeah, Ive already put in a new GM canister and...

    Yeah, Ive already put in a new GM canister and vent solenoid. I am not throwing any faults but from a cold start it must be running a test around 160 degrees and usually the afr will plummet to 12:1,...
  24. Replies
    15
    Views
    667

    Good to know. I had to go get gas and working out...

    Good to know. I had to go get gas and working out EVAP bugs still, then Ill try again.

    Im using this formula.
    ...
  25. Replies
    14
    Views
    696

    shift time is usually all you have to do, after...

    shift time is usually all you have to do, after that then start upping the oncoming pressures 5-10 ft lbs at a time, and that is usually only if it isnt meeting the desired time. To delve deep is to...
Results 1 to 25 of 427
Page 1 of 18 1 2 3 4