Search:

Type: Posts; User: GrannySShifting

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. PE commanded not matching whats shown in PE Enrich table???

    This is E40 pcm

    at 6000 rpm WOT and 169-170 kPa in both logs, can see its 8.11 target in one, 7.97 in other (10.11 stoich value at alcohol content in first for 1.246 PE ratio, 10.06 in second for...
  2. Kinda my point haha :) One seems to think...

    Kinda my point haha :)

    One seems to think think theres a hard wall limit when in speed density only mode using the VVE table for fueling at 255kPa being the cut, but it does it around 240 some kPa...
  3. Pretty sure I logged Fuel Cut status bit on some...

    Pretty sure I logged Fuel Cut status bit on some of the pulls, and fuel cut usually cuts it all not some?
  4. It sounds like you are saying you made every VE...

    It sounds like you are saying you made every VE table value 255kPa and above the same, and adjusted those values in each RPM column to get the air fuel you want one time on a dyno for example.
    ...
  5. In MAF mode where it will go past there, VE is...

    In MAF mode where it will go past there, VE is 2397where it looks like should be 2427 in table but no biggie

    91413


    Then 2484 as its running up (looks like 2530 in table to me it had just...
  6. Log is in link at the end of my last post I...

    Log is in link at the end of my last post

    I understand that the Volumetric Efficiency in scanner cant SHOW past 67.72, but its definitely using it in calculations well past that when in speed...
  7. I have a little bit, 25 years ago :) So well just...

    I have a little bit, 25 years ago :) So well just say no haha




    So do you have any insight on the other questions, or perhaps why it thinks it all the sudden has ton less Dynamic Airflow even...
  8. Yes, one of my guys said it was maybe a quart low...

    Yes, one of my guys said it was maybe a quart low but that was few weeks ago when it wasnt shifting at all WOT
  9. Dont know what your last two lines are about I...

    Dont know what your last two lines are about I guess your just showing the math how you got there?

    Do you know if there is a upper limit in boost you can run? (assuming MAP sensor can read it and...
  10. What are you talking about?

    What are you talking about?
  11. What are all the E67 airflow limits?

    HPTuners will only report Volumetric Efficiency Airflow to 67.76 lb/min but thats just what it shows theres no max is there? Any way to log what its actually calculating? (If its in Speed Density...
  12. 6L80e does some odd stuff, surging/hunting at WOT?

    Thought it was doing odd stuff downshifting but managed to get it to the floor in 2nd without it spinning and rpm wavers for a long while before it seems to get itself figured out and pulls normally...
  13. Fuel cuts and g/cyl plummets at certain boost level in SD, but not in MAF mode?

    What are the limits of boost you can RUN, vs what scanner reads (stops reporting MAP at 255 kPa), doesnt look like Maximum MAP limit has any affect on anything?
  14. The one I was trying to check was not

    The one I was trying to check was not
  15. I would THINK it would have to be set up with the...

    I would THINK it would have to be set up with the Supercharged Fitted switch set to yes maybe a couple other, and CTSV/ZL1 wiring diagram should tell you what you need. It is a funky OS though so....
  16. Can break out wiring and set up for a stand alone...

    Can break out wiring and set up for a stand alone baro sensor so its always sampling
  17. Airflow limit in Speed Density??? Doesnt do it in MAF only

    Been chasing my tail, thinking it was a torque value thing (calc torque down from 990s to near 700s and still did it) then maybe a gms/cyl thing (no because in MAF mode went well into the 2.x...
  18. On anti lag your TRYING to build boost, and few...

    On anti lag your TRYING to build boost, and few lbs. Lot different fuel volume at 9psi 4000rpm on 2 step then 36psi at 6800rpm full song
  19. Im not sure what in the world your looking at....

    Im not sure what in the world your looking at. They are virtual VE tables, there is no "limit" per se on the scalling. Screen shot what your looking at
  20. Finally someone noticed this, (I did on dyno) but...

    Finally someone noticed this, (I did on dyno) but there is no hole in the VE map its 2483 at 4400 235 kPa reports 2450. At 4535 rpm and 242 kPa table is @2500 and reports 2487 but you can already see...
  21. How are you overriding #1 What MAP config is...

    How are you overriding #1
    What MAP config is fixing #2
  22. use the Edit:Navigator and type in buzzwords for...

    use the Edit:Navigator and type in buzzwords for whatever you are looking for will help you find tables
  23. Readiness Monitors dont show in HPTuner anymore

    Any idea when this is going to be put (BACK) in?
  24. Replies
    10
    Views
    692

    Tune looks perfectly fine, not going to get much...

    Tune looks perfectly fine, not going to get much more timing in LS2 at least on the gas we have around here. Fuel trims arent wacked

    Narrowbands look ok. If its lacking midrange grunt its...
  25. If you cut ign with 1400hp worth of E85 in...

    If you cut ign with 1400hp worth of E85 in cylinder, things can hydrolock and bend rods and other fun stuff.

    RPM limits are never changed but does it with one pound more boost then stops if you...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4