Search:

Type: Posts; User: momotunes

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    29

    Knock Retard Valid Max

    Question.. I'm confused on this parameter. I'm having a hard time understanding the description. What exactly does the Knock Retard valid max do?

    Thanks everyone.


    92473
  2. Replies
    37
    Views
    589

    Is it possible different ECU handle the MAF data...

    Is it possible different ECU handle the MAF data differently? On mine, messing with the MAF to correct fueling (with correct injector data) just messed with drivability. Wheel torque error was...
  3. Replies
    8
    Views
    451

    Mines failing mid write on a F150. Won't detect...

    Mines failing mid write on a F150. Won't detect my mustang, and giving me issues connecting to my Silverado. HP suggested a bench harness. Doing the same thing. I updated the device firmware and...
  4. Replies
    6
    Views
    241

    92238 For virtual set this table flat across...

    92238

    For virtual set this table flat across and see if fuel trims improve.
  5. Replies
    6
    Views
    225

    When did they say they were going to remove...

    When did they say they were going to remove switchs??
  6. I believe just the exhaust temp table. If memory...

    I believe just the exhaust temp table. If memory serves me correctly it good by RPM and load.
  7. Hello. I got the small case.

    Hello. I got the small case.
  8. Replies
    6
    Views
    241

    Did your ethanol percentage go back up? I've...

    Did your ethanol percentage go back up? I've seen a lot of the flex sensors go bad and cause this exact issue. Disable flex, reset trims, and log to confirm.
  9. Replies
    3
    Views
    260

    You're correct. I'm sorry about the confusion.

    You're correct. I'm sorry about the confusion.
  10. Replies
    4
    Views
    215

    Thank you. This is an 04 as well. I'm going to...

    Thank you. This is an 04 as well. I'm going to try it. On a side note I remember now, when I made the axis the same it would throw a second and fourth gear incorrect ratio fault code and the...
  11. Replies
    73
    Views
    8,246

    Correct

    Correct
  12. Replies
    4
    Views
    215

    Sorry, overlap was a poor way to explain. What...

    Sorry, overlap was a poor way to explain. What happens is I run into issues where the torque converter locks and unlocks over and over. Of course in certain ranges I adjusted incorrectly. Same...
  13. Hahahaha that's a lot of posts you've read. You...

    Hahahaha that's a lot of posts you've read. You know I get mixed answers too or at least that's how I read them. Anyways I'm not sure on your engine but I'll explain what I did on my N/A built 5.4...
  14. I bought this from Amazon and it fit the device...

    I bought this from Amazon and it fit the device like it was made for it. Carrying Case for GoPro Hero 7 Black,6,5, 4, Black, Silver, 3+, 3,Hero(2018) and Accessories,HSU Protective Security Bag,...
  15. Replies
    17
    Views
    390

    Be easy on it until you get your wideband. Also,...

    Be easy on it until you get your wideband. Also, probably try putting MAF back to stock once you do install wideband and just keep working on slopes & minimum pulse width.
  16. Replies
    5
    Views
    249

    Be careful doing this. I know it helps in some...

    Be careful doing this. I know it helps in some areas to spray fuel after the exhaust valve closes with overlap but it can easily lead to cylinder washing. I use to do this too. When I changed my...
  17. Replies
    17
    Views
    390

    Increase slopes to decrease amount of fuel and...

    Increase slopes to decrease amount of fuel and decrease slopes to inject more fuel. Try lowering minimum pulse a tad too if you have too.

    Are you sure injectors are the issue? Did you try...
  18. Replies
    4
    Views
    215

    Torque Converter Lock & Shift Schedule

    Does anyone have a spreadsheet or method for adjusting shift points & torque converter lockup/release? I've tried a few different approaches on the torque converter lockup and I'm running into what...
  19. Replies
    17
    Views
    390

    Hi Mark - The data you have on your first...

    Hi Mark -

    The data you have on your first post looks correct & part number is just interchanged. Are your injectors the fatter style?

    Anyways I entered the data on your file. Start with...
  20. Replies
    3
    Views
    260

    04 f150 is the 3V motor. I think yours is a 2V...

    04 f150 is the 3V motor. I think yours is a 2V motor.
  21. Replies
    8
    Views
    268

    I'm not sure of the math of hand but I think I...

    I'm not sure of the math of hand but I think I have it on my computer. If I do I'll respond with it but I won't be near my computer for a few days.
    Try putting in a support ticket to hpt...
  22. Replies
    8
    Views
    268

    Use airload in the scanner. If you don't have...

    Use airload in the scanner. If you don't have that than you can use math to figure it out. Use one of HPT default maths. It would MAF cylinder airmass. Take that number and divide it by your engine...
  23. Replies
    10
    Views
    1,227

    Hahahaha yes they are!

    Hahahaha yes they are!
  24. Replies
    3
    Views
    129

    The cams can only retard. So 0=full advance and...

    The cams can only retard. So 0=full advance and +40= 40 degrees retard.
  25. Replies
    2
    Views
    191

    Not to start an argument or anything and I'm...

    Not to start an argument or anything and I'm saying this with no offense and disrespect... At least they give the option to use serial or AC/EGR input without the pro feature set. Even if you...
Results 1 to 25 of 135
Page 1 of 6 1 2 3 4