Search:

Type: Posts; User: HNK

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    341

    How would you go about tuning for humidity?

    How would you go about tuning for humidity?
  2. Replies
    57
    Views
    21,075

    I recently installed a baro breakout on my c7z....

    I recently installed a baro breakout on my c7z. Under wot, it reads 5 points higher, 104.5 vs 99.5. Any ideas on a fix? match values of LS3
  3. Thread: 2005 Viper

    by HNK
    Replies
    0
    Views
    70

    2005 Viper

    looking for a 2005 viper file
  4. Replies
    46
    Views
    2,382

    Ben, there are few throttle channels, which one...

    Ben, there are few throttle channels, which one should we pay attention to and should it be reading 100 at wot??
  5. Replies
    46
    Views
    2,382

    So is that false Kr for sure??? I get that...

    So is that false Kr for sure??? I get that sometimes on 2,5,6 2-3 deg. Are you planning to dyno it soon? maybe they have the proper tools to listen to see if its a real knock or false.
  6. Replies
    46
    Views
    2,382

    Can you elaborate a bit more on the static retard...

    Can you elaborate a bit more on the static retard and why on one cyl?
  7. Replies
    46
    Views
    2,382

    knock sensors??

    knock sensors??
  8. Replies
    46
    Views
    2,382

    the one after the Dsx install.

    the one after the Dsx install.
  9. Replies
    46
    Views
    2,382

    Can you post the second log ?

    Can you post the second log ?
  10. Replies
    46
    Views
    2,382

    Hi, Your throttle scalar hasn?t been changed for...

    Hi, Your throttle scalar hasn?t been changed for the 103mm Tb. Maybe that?s why your idle isn?t good
  11. Replies
    46
    Views
    2,382

    Ben, so pretty much the SOI shouldn't go over 360...

    Ben, so pretty much the SOI shouldn't go over 360 then? is that what causes a puff of smoke under hard acceleration?
  12. Replies
    56
    Views
    4,287

    By the way, why does delivered torque max out at...

    By the way, why does delivered torque max out at 640 while logging
  13. Replies
    56
    Views
    4,287

    Thx HB, realized after logging. A question, do...

    Thx HB, realized after logging. A question, do you run your car in SD mode or both? Why is it important to get the VVE dialed in if I will be MAF only? Would bumping the flow axis in the fuel pump...
  14. Replies
    56
    Views
    4,287

    What are the values in the VVE horizontal axis (...

    What are the values in the VVE horizontal axis ( the map/baro) represent? g/s?
  15. Replies
    38
    Views
    17,018

    in the spreadsheet, it calls for inputting AFR,...

    in the spreadsheet, it calls for inputting AFR, is that actual wideband read or commanded? also, since we need to power at wot open, over the 1.36, why would some populate pretty much all the area?
  16. Replies
    38
    Views
    17,018

    How does the AFR/Lambda get affected by this?...

    How does the AFR/Lambda get affected by this? lets say you are dialed in to a .84 lambda then do mod the SOI, any changes?
  17. Replies
    12
    Views
    1,320

    what Voltage are u running at the higher flow...

    what Voltage are u running at the higher flow areas?
  18. Replies
    12
    Views
    1,320

    No issues with the pump running the extra volts?

    No issues with the pump running the extra volts?
  19. Replies
    25
    Views
    982

    My highside gets to 2300 on my C7Z, would going...

    My highside gets to 2300 on my C7Z, would going to 24 Mpa get me back online? or hardware is needed at that point?
  20. Replies
    22
    Views
    4,217

    Sticky: Darek, hows the BT/wireless performance with the...

    Darek, hows the BT/wireless performance with the latest update? used to have issues with few channels showing before. did you guys fix all that?
  21. Replies
    4
    Views
    524

    Same here... Bill, any updates on this?

    Same here... Bill, any updates on this?
  22. Replies
    1
    Views
    249

    Mass airflow reading, C7z06

    Hi

    does the mass airflow reading max out at 86.69 Lb/m???
  23. Replies
    6
    Views
    609

    How did u go about the SOI changes? Dyno tuned...

    How did u go about the SOI changes? Dyno tuned them or just added in the areas were the HPFP needed help?
  24. Thread: MAF vs engine HP

    by HNK
    Replies
    6
    Views
    5,386

    I didn?t use a Dyno but I went from 68 lb/m to...

    I didn?t use a Dyno but I went from 68 lb/m to 86.69 lb/m but my 100-140 and beyond times in similar weather conditions stayed the same? You would think such air gain will show specially at those...
  25. 👍👍👍

    👍👍👍
Results 1 to 25 of 256
Page 1 of 11 1 2 3 4