Search:

Type: Posts; User: Ethan5.019

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    35
    Views
    1,943

    I'm actually changing my file now to have the...

    I'm actually changing my file now to have the manual cam control on but I wanted to clarify a couple cam angles and where does the ecm get the SD, Spark, Torque and ect for these manually selected...
  2. Replies
    35
    Views
    1,943

    Thats my mistake I meant retard. I also have not...

    Thats my mistake I meant retard. I also have not switched it to manual yet but that is my next step.
  3. Replies
    35
    Views
    1,943

    Here are the lastest file and log but my exhaust...

    Here are the lastest file and log but my exhaust cam still won't advanced and that is the only thing holding me back right now. Any insight or advice is greatly appreciated. You may even send me a...
  4. Replies
    35
    Views
    1,943

    How much more aggressive did you get with the cam...

    How much more aggressive did you get with the cam overlap on that mustang? Did you further reduce the Tables explained above? Also did you have to do any adjusting to the misfire detection when...
  5. Replies
    35
    Views
    1,943

    I just reviewed the file you attached and I was...

    I just reviewed the file you attached and I was wondering if you could explain what the Torque and Inverse Torque tables do? What is the Inverse torque?
  6. Replies
    227
    Views
    102,794

    It's all good I appreciate it.

    It's all good I appreciate it.
  7. Replies
    35
    Views
    1,943

    Do the Gen3s have the dashpot control? I've seen...

    Do the Gen3s have the dashpot control? I've seen this term in a few other threads and wasnt sure if the Gen3s had the ability to be locked in a certain table using the idle control.
  8. Replies
    35
    Views
    1,943

    Do you think my snap to point table has anything...

    Do you think my snap to point table has anything to do with the truck still going to MP0-1? That's the one table along with the snap to line table that I didn't really mess with because I didn't know...
  9. Replies
    20
    Views
    1,154

    Yeah I am experiencing a small surge in idle...

    Yeah I am experiencing a small surge in idle while the truck is warming up after I modified the CSER tables for Base Neutral and Base Neutral FFV
  10. Replies
    20
    Views
    1,154

    Did your idle get unstable when you changed the...

    Did your idle get unstable when you changed the Torque ratio clips?
  11. Replies
    227
    Views
    102,794

    Do you know if this will work on the Gen3 with...

    Do you know if this will work on the Gen3 with the 10r80? Its an F150 but I'm having a hard time getting my ghost cam settings to work and obey the distance tables.
  12. Replies
    20
    Views
    1,154

    Id have to find this in the Gen3 Calibration....

    Id have to find this in the Gen3 Calibration. I'll look though.
  13. Replies
    20
    Views
    1,154

    I want to say I modified the timing in the...

    I want to say I modified the timing in the Spark>Advance>Base Emissons Reduction table and had a positive result in taking the cold start. I change all the negative values to 0 and I'm also going to...
  14. Replies
    35
    Views
    1,943

    114223 114224 These are the most recent...

    114223

    114224

    These are the most recent Revision and log for the continuing battle for the Ghost cam. The truck still wont lope.
  15. Replies
    20
    Views
    1,154

    I was looking at adjusting my cold start as well...

    I was looking at adjusting my cold start as well since I'm now catless and my logged Spark Source says Torque Control. The CSER table is under the Torque Management Tab so would this be the same...
  16. Replies
    35
    Views
    1,943

    I just figured I'd ask and gather any knowledge...

    I just figured I'd ask and gather any knowledge that's out there on it. I'll write the calibration with the 20609 adjusted for more phasing at lower Temps and less run time
  17. Replies
    35
    Views
    1,943

    So i changed the table 20609 and started digging...

    So i changed the table 20609 and started digging a little more and Idle>RPM>Minimum setpoint (Table 10021) is set my intake cam angle. I assume since we are dealing with Exhaust cam angles this table...
  18. Replies
    35
    Views
    1,943

    114198 I am already logging the Cam Angle and...

    114198

    I am already logging the Cam Angle and Cam error so would I add the Cam Des Angle or the Cam Angle DC?
  19. Replies
    35
    Views
    1,943

    This was where it was originally. 114157

    This was where it was originally.

    114157
  20. Replies
    35
    Views
    1,943

    114155 114156

    114155

    114156
  21. Replies
    35
    Views
    1,943

    My Setup is a 19 F150 5.0 10R80 170* T-stat,...

    My Setup is a 19 F150 5.0 10R80 170* T-stat, longtubes and cat delete. Nothing overly complicated.
  22. Replies
    35
    Views
    1,943

    114151 114152 These logs are the most...

    114151

    114152

    These logs are the most recent and I locked it in OS but its still reverting to MP 0 and 1. I have MP8 plugged into the distance table and OS Mapped Points.
  23. Replies
    35
    Views
    1,943

    Are there any torque values under Idle> Torque...

    Are there any torque values under Idle> Torque tab that need adjusted to compensate?
  24. Replies
    48
    Views
    18,813

    I'm attaching a tune file and log for my ghost...

    I'm attaching a tune file and log for my ghost cam settings on my F150. I know I'm missing something but I cant seem to find that link. Any help is appreciated thank you. I've locked the truck in...
  25. Replies
    35
    Views
    1,943

    Needing a little guidance if I may have missed a...

    Needing a little guidance if I may have missed a table. The truck won't take the commanded MP I have input for the Optimum Stability table. It reverts to the Emissions reduction table and then goes...
Results 1 to 25 of 36
Page 1 of 2 1 2