Search:

Type: Posts; User: Higgs Boson

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    33

    I run completely stock DD and VT with 1000 rwhp...

    I run completely stock DD and VT with 1000 rwhp on E85. You don't need to change them.
  2. Replies
    6
    Views
    209

    https://forum.hptuners.com/showthread.php?4742-REA...

    https://forum.hptuners.com/showthread.php?4742-READ-ME!!!-General-tuning-info-and-how-to-s

    https://forum.hptuners.com/showthread.php?9700-Read-Me!!!-Tuning-How-To-s-amp-General-Information
    ...
  3. As mentioned, when the TCM gets the unlock...

    As mentioned, when the TCM gets the unlock service, the only thing readable is a generic file. You will not be able to read what you wrote to it.

    If you are saying that you can't read anything at...
  4. Replies
    2
    Views
    118

    i don't update that table on LT1's with LT4 parts.

    i don't update that table on LT1's with LT4 parts.
  5. i don't remember, I just saved the list and don't...

    i don't remember, I just saved the list and don't change it
  6. Replies
    9
    Views
    221

    40 is a default value, sounds like it's hooked up...

    40 is a default value, sounds like it's hooked up wrong or it's a bad sensor.
  7. Description says Compressor Speed to Engine Speed...

    Description says Compressor Speed to Engine Speed even though the name of the field is Pulley Ratio.

    GM rated the max blower speed on the LT4 at 20,150 which would be 6,740 at the engine.

    Not...
  8. There has been two MAT's for the LT engines since...

    There has been two MAT's for the LT engines since 2013.

    I logged both and compared the output to the IAT retard output based on the IAT table and decided which to delete and which to keep.
  9. Replies
    9
    Views
    221

    Will probably never update sitting idling at the...

    Will probably never update sitting idling at the gas station. In my experience it takes a good 4 miles of normal driving to update.
  10. oxygen sensors switch around the stoich of the...

    oxygen sensors switch around the stoich of the fuel in the tank, not the value in the tune.

    this means that if you are running E10 your O2 sensors will switch around stoich for E10.
    if you run E0...
  11. Replies
    15
    Views
    308

    I have a 2019 with an SB intake and another...

    I have a 2019 with an SB intake and another modification. I only adjust Tq2Fuel Config 1 Mode 0, 1032 row to 160 and bump it and smooth it a little bit below that. I leave the Smoke Limiter stock,...
  12. post your tune.

    post your tune.
  13. Replies
    28
    Views
    1,285

    no need to reread to see new tables (ever). just...

    no need to reread to see new tables (ever). just need the HPT version with the ability to display them.
  14. Replies
    28
    Views
    1,285

    I will say I will probably revise some of the...

    I will say I will probably revise some of the decel areas back to stock or near stock values, need to log it and see which areas though. Coming off pedal to 0% sometimes feels a little too quick or...
  15. Replies
    9
    Views
    175

    did you disable cat overtemp and other potential...

    did you disable cat overtemp and other potential similar?
  16. Replies
    9
    Views
    175

    The OL tables aren't used like that on these...

    The OL tables aren't used like that on these ECMs.

    If you were getting the same AFRs no matter what PE you commanded, what did you command and what did you get?
  17. Replies
    28
    Views
    1,285

    Mine is a 2017 Z06 and I also had them added to...

    Mine is a 2017 Z06 and I also had them added to my wife's 2019 Yukon OS. If you don't see them then HPT can add them if you send your file to support.

    I also had them added to a 17 Yukon customer...
  18. Replies
    28
    Views
    1,285

    all of them. Predicted and Immediate Increasing...

    all of them. Predicted and Immediate Increasing and Decreasing. And Disabled the Idle one.

    All Decreasing is -6041
    All Increasing is 6041
  19. Replies
    28
    Views
    1,285

    I maxed out the tables -6040 and +6040 and the...

    I maxed out the tables -6040 and +6040 and the pedal/throttle definitely feels and works like one might think it should. Very nice.

    Now I am returning to the Driver Demand tables to see if I get...
  20. Replies
    4
    Views
    149

    I am aware of past conversations about it. ...

    I am aware of past conversations about it. Doesn't answer the question.
  21. Replies
    4
    Views
    149

    have we logged IVT on different scanners? How do...

    have we logged IVT on different scanners? How do we know it's a bug in the HPT Scanner?

    Many IVT tables have the high load negative values populated uniquely which leads me to wonder if it is a...
  22. Replies
    11
    Views
    1,561

    that's not really the answer to a question being...

    that's not really the answer to a question being asked.
  23. are you sure it isn't just super rich? pull 20%...

    are you sure it isn't just super rich? pull 20% out of the VVE and see if it runs.
  24. Replies
    28
    Views
    1,285

    Torque Request Rate Limits

    Anyone using these tables yet?

    Just noticed them in the Driver Demand section.
  25. https://forum.hptuners.com/showthread.php?50302-St...

    https://forum.hptuners.com/showthread.php?50302-Start-of-Injection-calculator&highlight=calculator
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4