Search:

Type: Posts; User: 2000_SS

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. To clarify, it was a dual nozzle kit and the car...

    To clarify, it was a dual nozzle kit and the car is a long ways from needing that much meth.
  2. Ok so i eliminated one of the meth nozzles and...

    Ok so i eliminated one of the meth nozzles and moved the remaining one towards the intercooler, further away from the mass airflow sensor so the IAT would see the meth... Now the MAF frequency goes...
  3. Tuning meth injection... Quick question for sanity check

    I have a C6 with a A&A kit on about 8psi, mild cam, exhaust, and a 3400 or so converter... The Alky Control kit was installed after a previous tuner hacked the tune up and I'm basically starting from...
  4. Got it running finally....turns out the figures...

    Got it running finally....turns out the figures in the VE weren't NEARLY big enough...
  5. no changes with adding/subtracting base airflow

    no changes with adding/subtracting base airflow
  6. MAF is being ignored, there isn't one, the...

    MAF is being ignored, there isn't one, the airflow table is left stock in case zeroing it out prevents the truck from starting before speed density kicks in.

    I'll play with the idle airflow and...
  7. Could it be too much bass idle air flow? It ran...

    Could it be too much bass idle air flow? It ran when it drove to my house with the same figures in that table though.
  8. starts and dies after 2 bar OS application

    working on a 2008 silverado....6.0 engine, smallish cam, On3 turbo, FIC 650cc, 3200 circle D, 4L80E...double stoich/half IFR...The truck drove in on a 1 bar OS, rough running, owner tried tuning...
  9. Replies
    2
    Views
    123

    Burst knock was the culprit.... forgot to log it,...

    Burst knock was the culprit.... forgot to log it, :banghead:
  10. Replies
    2
    Views
    123

    Crank relearn didn't help either.

    Crank relearn didn't help either.
  11. Replies
    2
    Views
    123

    Jagged spark under WOT

    Anybody know what causes the shark tooth looking spark advance when i go WOT? I can't figure it out. I've seen this on one other car. Could it be a bad crank sensor or bent reluctor? or am i missing...
  12. Replies
    0
    Views
    323

    Interface not found

    On 3 different laptops, and also with my old mpvi pro, i always get an "interface not found" message when i try to flash a vehicle.

    When i unplug the usb and plug it back in, it will flash and...
  13. Replies
    1
    Views
    198

    AEM replacement sensor question

    Is the Bosch 17025 the correct replacement sensor for an AEM 30-0334? I believe it is but can't find concrete confirmation online.

    Thanks
  14. Replies
    1
    Views
    170

    2017 Z06 stock file needed

    Anybody have a stock 2017 Z06 file? I don't see one in the repository....TIA.
  15. Mechanical VVT/AFM delete performed due to lifter...

    Mechanical VVT/AFM delete performed due to lifter failure -> test drive, fired up and ran fine but with WOT issues -> 2nd test drive with scanner running that went haywire during WOT -> write entire...
  16. Grounds are good. The car ran and drove. The no...

    Grounds are good. The car ran and drove. The no crank issue just started after a write entire was performed... no mechanical changes were made.
  17. Here's the tune in the car now as it sits

    Here's the tune in the car now as it sits
  18. Help! no crank / no start after a write entire - other issues after DoD/VVT delete

    I wrapped up a DoD/VVT delete on a 2012 SS camaro today. After i flashed it with just codes disabled, i took it for a drive. everything seemed fine until i stabbed the throttle. It cut out and pulled...
  19. Replies
    12
    Views
    509

    Post back with your results

    Post back with your results
  20. Replies
    12
    Views
    509

    For starters, i would recommend downloading the...

    For starters, i would recommend downloading the Bluecat Transmission tool and using it to set your shift points. That will help a lot. I would set the torque management settings back to stock in the...
  21. Replies
    2
    Views
    226

    That's not really how it works around here. You...

    That's not really how it works around here. You aren't going to have anybody just give you a tune. If you want, there are a TON of threads on here you can search for regarding what changes to make....
  22. Replies
    17
    Views
    544

    Need to know exactly what brand the injectors...

    Need to know exactly what brand the injectors are. If you don't know, see what numbers or markings are printed or engraved on them. The injector characterization data is a critical part of the tune....
  23. Replies
    2
    Views
    274

    troubled downloading VCM suite?

    When i try to download VCM suite it makes it 4-6MB in and stops, saying "Failed - File Incomplete." I can click on "resume" and it will eventually download, but it only goes 5MB or so at a time...
  24. Both O2 sensors were bad. We just replace them...

    Both O2 sensors were bad. We just replace them and everything is fine now.
  25. Replies
    11
    Views
    737

    I never observed the VCP spark actually doing...

    I never observed the VCP spark actually doing anything. The truck appeared to only be using the high octane spark table. I don't know if it matters, but this is an E38 swapped truck with a TH400, so...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4