Search:

Type: Posts; User: SteveMcQouy

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    1,313

    No I wasn't getting any blow by like I was when...

    No I wasn't getting any blow by like I was when the teflon seal on one my injectors seemed to be swallowed up by my motor. The injectors were sealing to the block. However, they don't seem to be have...
  2. Replies
    8
    Views
    1,313

    Just wanted to post a conclusion. It was not a...

    Just wanted to post a conclusion. It was not a vacuum leak or anything else with the car. I did vacuum test everything and everything held vacuum. I ended up getting a seal kit for the factory...
  3. Replies
    8
    Views
    1,313

    Just out of curiosity, what is it that you see...

    Just out of curiosity, what is it that you see that makes you believe vacuum leak?
    I don't have access to a smoke machine. Might be able to find a local shop with one if need be. I was planning to...
  4. Replies
    8
    Views
    1,313

    Audi 3.0t B8.5 Fuel Injector Issue

    I have a 2013 Audi S5. Been tuned with HP now for several years and have had some help here in the past so hopefully we can figure this out.
    I just bought all new injectors from ECS Tuning...
  5. Replies
    59
    Views
    16,979

    Very interesting, you wouldn't happen to know why...

    Very interesting, you wouldn't happen to know why my torque tables were limiting the power before TylerDubbs did some editing for me?
    Also would you know how to go about recalibrating the airflow...
  6. Replies
    59
    Views
    16,979

    I expanded the table so that it would go to the...

    I expanded the table so that it would go to the new SC rpm limit of roughly 24k and extended P.R. as well to roughly what was being logged
  7. Replies
    59
    Views
    16,979

    I always wondered if it was a MAF sensor. There...

    I always wondered if it was a MAF sensor. There is a sensor going into the SC housing right after the TB. So you're saying they are all pressure sensors? Why not use a MAP based tuning style then,...
  8. Replies
    59
    Views
    16,979

    I did have the throttle body and blower ported by...

    I did have the throttle body and blower ported by a machine shop. Not sure how much they actually did, never noticed a difference but when I had the motor out the 1st time I had it done.
  9. Replies
    59
    Views
    16,979

    Went out with TC off, did some pulls. Still some...

    Went out with TC off, did some pulls. Still some hiccup that can be see in the MAF. However during a 4th gear pull, my bypass valve decided to get stuck closed. Not the first time as they are stupid...
  10. Replies
    59
    Views
    16,979

    It was with this file, however I run 17" rims...

    It was with this file, however I run 17" rims with my snows so the side walls are a lot taller. I believe the soft sidewalls have been messing with the traction control as I did notice the light come...
  11. Replies
    59
    Views
    16,979

    Interesting there would be a multiplier, do you...

    Interesting there would be a multiplier, do you think that's something in the background that HPTuners does not show us? I'm going to continue to work on the non meth tune for now. I think I need to...
  12. Replies
    59
    Views
    16,979

    Meth is hooked up to my intake pipe coming from...

    Meth is hooked up to my intake pipe coming from the cone to the throttle body. I'm using a 500cc injector. There is a very good forum on this engine and all things meth here:...
  13. Replies
    59
    Views
    16,979

    Got some logs with and with out meth, nice cold...

    Got some logs with and with out meth, nice cold day for boost.
    Regular run: 3rd gear at 12:16:06 3rd into 4th gear at 12:17:54

    Meth Run: 3rd gear 12:19:21 3rd into 4th 12:20:54 3rd...
  14. Replies
    59
    Views
    16,979

    Will do, we got 8.5" of snow last night!! So I'll...

    Will do, we got 8.5" of snow last night!! So I'll go out tomorrow and do some logs with and w/o meth plugged in
  15. Replies
    59
    Views
    16,979

    I have an AEM meth kit that I run almost 24/7 in...

    I have an AEM meth kit that I run almost 24/7 in the summer. I run the blue windshield washer fluid that's only (water/meth/and blue dye). I do not run it while tuning as I don't want to rely on it....
  16. Replies
    59
    Views
    16,979

    No unfortunately it's how the vehicle is, all...

    No unfortunately it's how the vehicle is, all Audi's that I've messed with, with a manual gearbox are like that from factory. It has a 4k rpm limit stock but with traction off and clutch in, it will...
  17. Replies
    59
    Views
    16,979

    Thank you very much for the help, those TQ tables...

    Thank you very much for the help, those TQ tables are tricky lol.
    One last question if you happen to know much about Audi. The car is a manual gearbox and when I 2-step it with traction control off...
  18. Replies
    59
    Views
    16,979

    Ok that makes sense, new added timing had a lot...

    Ok that makes sense, new added timing had a lot of knock, however I have messed with the min spark tables a lot not knowing that was a NO NO. I'll put those back to stock other than pulling timing...
  19. Replies
    59
    Views
    16,979

    Thank you!! It's the tuned inversely that I don't...

    Thank you!! It's the tuned inversely that I don't understand. For some reason my VCM software does not have the inverse calculator, not sure if I'm supposed to use that or something like that. I'll...
  20. Replies
    59
    Views
    16,979

    Great Success!!!!! I built Torque tables last...

    Great Success!!!!!
    I built Torque tables last night too, however I rebuilt my whole table and that lead to me in limp mode..... ooops
    Your torque table build worked, this data log is with it. Best...
  21. Replies
    59
    Views
    16,979

    Ok I'll look into that. I also rescaled the...

    Ok I'll look into that. I also rescaled the "Airflow/Supercharger" "Airflow table". Stock was limited to 18k rpm and it's spinning up to the 24k range. Which odly enough, 18k rpm at the SC is 5500...
  22. Replies
    59
    Views
    16,979

    This is what was on the car for the second data...

    This is what was on the car for the second data log, I updated it from the first one so I don't have the one for the first data log.
  23. Replies
    59
    Views
    16,979

    I made the changes and did some logs, the first...

    I made the changes and did some logs, the first log is with the changes you made. The MAF is still staying around the 375 g/s so I guess we can rule out the Airflow table since there was no drop...
  24. Replies
    59
    Views
    16,979

    More of the same with some other pulls. I have a...

    More of the same with some other pulls. I have a decent amount of data logs with this happening. I daily the vehicle its very noticable when it goes from 20psi to 13psi.
  25. Replies
    59
    Views
    16,979

    Yes I agree with the torque tables, mostly just...

    Yes I agree with the torque tables, mostly just high to ensure that's not what is cutting power anywhere. Mostly relying on the MAP limit table right now until the whole power drop off. I guess what...
Results 1 to 25 of 32
Page 1 of 2 1 2