Search:

Type: Posts; User: kevmo777

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,474

    6t75 desired slip??

    Help me understand the desired slip tables for the trans-torque converter-general-tcc desired slip? In 6th gear the lowest value is 20. Why would you want the TCC to slip at cruising speed?
  2. Replies
    6
    Views
    3,487

    Why can't I find the channel for pilot timing in...

    Why can't I find the channel for pilot timing in the scan tool?
  3. Replies
    6
    Views
    3,487

    2003 pilot injection

    I cannot find the scan channel for the pilot injection timing. I can find for the pulse width and quantity, but not the timing. Did 2003 have pilot injection?? All the tables in editor are...
  4. Replies
    6
    Views
    2,481

    I expierenced the same problem w/ my ls-6 and...

    I expierenced the same problem w/ my ls-6 and found that I needed to disable the COT protection while tuning. This fixed my problem.
  5. Replies
    1
    Views
    1,590

    Cranking VE tables

    When I start my car, it seems to 'rev' up to 1500 rpm upon starting-with my foot off the gas pedal and then settle down to idle (850). What do I need to tune for the car just to start and come up to...
  6. Replies
    13
    Views
    10,415

    Is that the reason that why I'm not getting the...

    Is that the reason that why I'm not getting the results I'm looking for? Do I need to be concerned about hurting my cats? I'm running high flow cats, w/ my rear o2 still enabled, that is why I...
  7. Replies
    13
    Views
    10,415

    Where can I find that supplement? Thanks.

    Where can I find that supplement? Thanks.
  8. Replies
    13
    Views
    10,415

    This is the document I was using "Tuning the...

    This is the document I was using "Tuning the Right Way" by Bob Morrale. See attachment for pages explaining pe tuning.

    I'm understanding the proper way to tune using maf/ve tables, but could...
  9. Replies
    13
    Views
    10,415

    So then, if I set my table to read afr of 13:1...

    So then, if I set my table to read afr of 13:1 and I'm reading 12:1, do I adjust my ve table and maf at the same time or seperate (like the fuel trims)? This case I would subtract from the ve table...
  10. Replies
    13
    Views
    10,415

    PE tuning-confused???

    I'm satisfied with my ve table, maf table and spark table, now I'm working on my PE table. All that I've read tells me that if my afr is low <12.7 that I need to subtract from my table and add if...
  11. Replies
    7
    Views
    3,606

    That did it!! I knew it had to be something...

    That did it!! I knew it had to be something simple! (it always is). Thank you for your help!!
  12. Replies
    7
    Views
    3,606

    Here is the screenshot

    Here is the screenshot
  13. Replies
    7
    Views
    3,606

    I don't understand, on my #4 user defined...

    I don't understand, on my #4 user defined parameters Air Fuel Ratio, the function string is using 7101 PID. Where do you see that I'm using PID 2811? Am I missing something? Thanks for the help.
  14. Replies
    7
    Views
    3,606

    Air Fuel Ratio not logging

    I have tried all I know a searched the forum over trying to get my AFR to log. Every time I connect I get a 'unsupported parameter'. I'm using my wideband through my A/C voltage to input the...
  15. Replies
    2
    Views
    3,020

    I got the problem 'unable to parse log' and tried...

    I got the problem 'unable to parse log' and tried the click and drag, but it will not let me drop it in the scanner. I also have some saved but when I do the file open from the scanner, I can't find...
  16. Replies
    1
    Views
    2,366

    Man do I feel stupid (more like humiliated). Now...

    Man do I feel stupid (more like humiliated). Now I know what happens when the coil pack on the right side is unplugged. The car run so good at idle, I didn't even realize it was not firing on the...
  17. Replies
    1
    Views
    2,366

    02 sensors on header install

    This is my next challenge. 2001 corvette z06, just installed long tube headers(coated) and high flow cats. I knew there may be issues w/ o2 sensors not working properly, so I wanted to check them...
  18. Replies
    4
    Views
    2,725

    Well, I read the sticky bout using outside power...

    Well, I read the sticky bout using outside power source, but I thought that it was referring to car charger adaptors for the laptop. I did not realize that it was for wall outlets too. I unplugged...
  19. Replies
    4
    Views
    2,725

    Laptop is a dell inspirion 1100 running xp. Is...

    Laptop is a dell inspirion 1100 running xp. Is there any fix besides getting new laptop?
  20. Replies
    4
    Views
    2,725

    Read Entire give no comm message

    I can connect w/ scanner and read information and save logs, but when I go to editor and try to read the VCM I get the attached screen shot. I check pin 16 on obd port and get batt voltage. Why...
  21. Thread: Rear 02s

    by kevmo777
    Replies
    12
    Views
    7,901

    I just installed long tube headers and high flow...

    I just installed long tube headers and high flow cats and wanted to check the 02s and ensure they are working correctly. I know for the fronts, I'm looking for switching after heat up-what do I look...
  22. Replies
    16
    Views
    7,760

    Well I would have thought that with the power...

    Well I would have thought that with the power light on the mpvi interface coming on when I plug it up to the laptop that the usb cable was good-WRONG. Changed the usb cable and everything worked...
  23. Replies
    16
    Views
    7,760

    Is there a phone # that I can call?

    Is there a phone # that I can call?
  24. Replies
    16
    Views
    7,760

    No,but it dosen't appear to change any if I...

    No,but it dosen't appear to change any if I unplug or plug in the mpvi. Here is one w/ it plugged up.
  25. Replies
    16
    Views
    7,760

    Looked up the demos on taking sceen shot-it was...

    Looked up the demos on taking sceen shot-it was blank, but see if this works-

    check the attachment
Results 1 to 25 of 29
Page 1 of 2 1 2