Search:

Type: Posts; User: deanm11

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    42
    Views
    20,392

    There's physically locking the cams. Then there's...

    There's physically locking the cams. Then there's tuning them that they don't change position. What are trying to do? With certain builds I think you need to to physically change the phasers so...
  2. Replies
    66
    Views
    26,593

    Middle pin of the AC pressure sensor connector...

    Middle pin of the AC pressure sensor connector works for logging.

    - USA made 2 bar sensor... 5v power & ground, middle pin is sensor output
    - add a circuit fused power off the underhood block to...
  3. Replies
    66
    Views
    26,593

    May I ask - did you get feed 5v power for the map...

    May I ask - did you get feed 5v power for the map sensor from the AC connector, or elsewhere? Can you tell me what pins get output connections from the map sensor?
    I plan to use this 2bar GM one.
    ...
  4. Replies
    25
    Views
    2,649

    I've given this some thought as I have an Alky...

    I've given this some thought as I have an Alky control kit, Snow meth ring, Devil's own nozzles on the shelf for when I thought I was going to go Forced induction.

    These motors have lots of room...
  5. "Tuned" up the tune with the ability to...

    "Tuned" up the tune with the ability to scrutinize the dynojet files and log files.
    Fixed my PE not going below 0.85/0.86. It was too high a minimum combustion stability.
    Fixed intake volume, also...
  6. Replies
    42
    Views
    20,392

    Sorry never saw the response about oil. I'm...

    Sorry never saw the response about oil. I'm trying Valvoline European 5w40. When really warm, I do sometimes a little clacking from the right bank. I'm not sure if I have a bad tensioner or phaser. I...
  7. I'm peaking about 50.3lbs/min (adjusted by trims)...

    I'm peaking about 50.3lbs/min (adjusted by trims) while air load is 0.882 at that time. Again, my VE / torque tables aren't really tuned. I'm at least just getting cams/spark and fuel at WOT and dyno...
  8. Thank you for that. I see my trims are a little...

    Thank you for that. I see my trims are a little positive too so a bit over 50. Comparing to the log when I made 460s, MAF is +4lb or so. (that pre-cams/Holley log attached)

    I know my speed density...
  9. Will report track results. This dyno isn't lying....

    Will report track results. This dyno isn't lying.

    I don't know why my mass air reads low.
  10. '22 Mustang GT FBO Comp Cams + new Holley intake, Results Dyno proven best Cam angles

    130722

    FBO car on E85 (tests 80%)
    Kooks longtubes, full aftermarket exhaust
    Highest Comp Cams NSR, retaining phasers
    ugpraded valve springs, GT350 tensioners, chains, electric water pump
    New...
  11. No start fixed. I reverted to my pre-Holley and...

    No start fixed. I reverted to my pre-Holley and Bullitt tune but for the IRMC switch basically and it starts fine.

    Now I guess I'll do only predicted throttle angle, effective area and throttle...
  12. Bullit TB on 2022 Mustang GT - Tables not common (?)

    I installed the Bullit TB (FMS-M-9926-M50B) along with the new Holley intake.

    I copied all the throttle body tables I could. What am I supposed to do with the data shown in the attached? These...
  13. Thank you. I'll try that.

    Thank you. I'll try that.
  14. Gen3 Coyote Tuning - General question about street tuning

    I have the MPV12 non pro interface. I'm at the point with my 2022 Mustang GT FBO + Cams build where I'm looking to tune which in reality is
    probably a max of 10-15 total HP from my previous FBO dyno...
  15. Replies
    42
    Views
    20,392

    Zero valvetrain / mechanical issues before the...

    Zero valvetrain / mechanical issues before the cams? Seems odd that you'd be going to MP28, I don't think I ever see it being used.
  16. Replies
    42
    Views
    20,392

    Here's my tune so far. I fiddled with the map...

    Here's my tune so far. I fiddled with the map point VCT but haven't attempted tuning the Optimum Power VCT yet.

    Car is FBO - full exhaust, E85 testing at about 70%...

    I did about 475 before...
  17. Replies
    42
    Views
    20,392

    Happy to look.. I'm still figuring out the...

    Happy to look.. I'm still figuring out the tuning... including part throttle VCT. You mean you aren't seeing the phasers respond? no codes or wrench light?
  18. Replies
    42
    Views
    20,392

    I did the highest "NSR" comp cams in my 2022....

    I did the highest "NSR" comp cams in my 2022. Early days but it runs great, appears to have full VCT control.
    I added MMR's lightweight VCT plates (intake only) and did valve springs on the car, as...
  19. Replies
    6
    Views
    3,771

    OP: Have you made the Suncoast VB work well,...

    OP: Have you made the Suncoast VB work well, what is you applicaiton? Any software tuning required besides the one above? I have one ready to install but I'm hearing mixed reports of them...
  20. Update/conclusion: Mechanical fault. Totally...

    Update/conclusion:

    Mechanical fault. Totally coincidental that this popped up right after my header and full exhaust install and tune update.... Swapped the front hubs L-R and the tone wheel code...
  21. Update: I have a friendly 3rd party shop that...

    Update:

    I have a friendly 3rd party shop that can do all the IDS operations I need.

    I think the ABS module pulses before it throws the codes - I thought I had an unrelated clunk kind of sound...
  22. Update: With the better Forscan cable it seems I...

    Update: With the better Forscan cable it seems I get more data on the fault that seems to all derive from ABS. I am more suspicious of something physical now. I separately have a little brake noise...
  23. Finally checked the logs - you are correct, while...

    Finally checked the logs - you are correct, while I command -26 at around 3500rpm, the resulting timing doesn't get past about -19/-21 Cam & Cam2 Angle
  24. I've been looking over wiring and haven't see...

    I've been looking over wiring and haven't see anything suspicious yet. I ordered one of the two Forscan recommended cables this time, though not the one you say. With the cheaper non-recommnded one I...
  25. Thanks for watching and giving ideas. I will...

    Thanks for watching and giving ideas. I will report after the new cable is in hand. Then I'm on to finding someone with the Ford tool. The speed required to trip the lights is interesting.. might be...
Results 1 to 25 of 210
Page 1 of 9 1 2 3 4