Search:

Type: Posts; User: Tapout Tuning

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Yes, check table 33913 - Injector SOI Base. Here...

    Yes, check table 33913 - Injector SOI Base. Here you can program the start of the injection angle (SOI) in crankshaft degrees BTDC.
  2. Replies
    28
    Views
    1,325

    Which ones did you change? I see 9508 (enable...

    Which ones did you change? I see 9508 (enable bit), 9509 through 9512 (decreasing) and 9513 through 9516 (increasing).
  3. Replies
    28
    Views
    1,325

    I'm curious about these new tables as well.

    I'm curious about these new tables as well.
  4. Replies
    4
    Views
    362

    I used to always struggle with this as well. One...

    I used to always struggle with this as well. One day I realized that the credit card expiration field works differently than shown. I believe they show it in this format: '09/19', but you actually...
  5. Replies
    4
    Views
    703

    I'll give you a good deal on a new set of Gen V...

    I'll give you a good deal on a new set of Gen V tuning books. Email me at ScottC@TapoutTuning.com if you're interested.
  6. You can order it with no credits, or preloaded...

    You can order it with no credits, or preloaded with two, four, six, etc.


    No.


    Patience is one of my virtues. ;)
  7. Replies
    4
    Views
    227

    I'm also interested! Best way to contact me is...

    I'm also interested! Best way to contact me is via email at ScottC@TapoutTuning.com.
  8. Replies
    18
    Views
    933

    If you just use the histogram's 'Average'...

    If you just use the histogram's 'Average' function it will ignore cells with no data, rather than assuming they're zeroes.
  9. Sometimes I wish this forum had a LIKE button.

    Sometimes I wish this forum had a LIKE button.
  10. I like this idea.

    I like this idea.
  11. Replies
    18
    Views
    1,260

    Ticket ID: 172540 Subject: MVPI Firmware...

    Ticket ID: 172540
    Subject: MVPI Firmware Update Failed
    Department: Support (Existing Customers)
    Type: Issue
    Status: Open
  12. Replies
    18
    Views
    1,260

    I'm having the same exact issue. Firmware...

    I'm having the same exact issue. Firmware upgrade won't complete no matter what I do, and now interface can't be found when I try to connect. Stranded at the drag strip as I type this.

    89633
  13. Replies
    0
    Views
    181

    E92A Launch Control Mystery

    During Launch Control mode, the commanded fuel injector pulsewidths are 0.0 milliseconds, the narrow band oxygen sensors show no voltage and this is confirmed by the wideband oxygen sensor. Can...
  14. Replies
    1
    Views
    112

    Meant to post this in the Gen V section. Sorry...

    Meant to post this in the Gen V section. Sorry about that.
  15. Replies
    1
    Views
    112

    E92A Launch Control Mystery

    During Launch Control mode, the commanded fuel injector pulsewidths are 0.0 milliseconds, the narrow band oxygen sensors show no voltage and this is confirmed by the wideband oxygen sensor. Can...
  16. Thank you!

    Thank you!
  17. HP Tuners Support has been very helpful locating...

    HP Tuners Support has been very helpful locating several previously undefined tables. However, I've sent this one to them two or three times. Each time they tell me they can't locate it.
  18. To the top, hoping someone can point me in the...

    To the top, hoping someone can point me in the right direction for this...
  19. Replies
    5
    Views
    507

    That looks great. Thanks for sharing! Have...

    That looks great. Thanks for sharing!

    Have you used this with an E92 ECM? And did you have to do anything special to keep the ECM from not being happy with the engine speed not doing what was...
  20. Seeking E92 Guru with User Defined Parameters Skillset

    I am looking for someone to help with locating and defining a specific table in the E92 ECM. Have a pretty good idea what it does and looks like, but don't have the ability to locate and define it. ...
  21. Replies
    5
    Views
    507

    E92 Two Step Launch Control

    Has anyone had success adding a two step rev limiter to the E92 ECM? Forum search doesn't really bring up much content from the current decade.

    If you've pulled this off, can you share the best...
  22. Very nice!

    Very nice!
  23. Please add the following parameters to your scan...

    Please add the following parameters to your scan log:

    Desired Boost
    Boost Pressure

    Engine Torque
    Peak Engine Torque

    Compare the first two to each other, relative to when the throttle is...
  24. Replies
    2
    Views
    310

    Wasn't aware of that. But it makes total sense,...

    Wasn't aware of that. But it makes total sense, since the ECM didn't seem to be attempting to scale things back.

    Appreciate the information!
  25. Replies
    2
    Views
    310

    E92A Peak Engine Torque

    Does anyone know how to increase the Peak Engine Torque limitation on the E92A ECMs above the 879 foot-pounds threshold? No matter how I set up the Peak Engine Torque table, I still get a flatline...
Results 1 to 25 of 126
Page 1 of 6 1 2 3 4