Search:

Type: Posts; User: [email protected]

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    580

    So I have looked at a lot of files. I have 2 I...

    So I have looked at a lot of files. I have 2 I would use. But now what. Close the current file, Open the new one and write entire. Then copy over my tunned parts of the old file to the new one??...
  2. Replies
    4
    Views
    580

    Is it possible to switch operation systems...

    Is it possible to switch operation systems completly. I have done sagment swaps but never looked at change complete operating systems
  3. Replies
    4
    Views
    580

    Trans park neutral switch

    i would like to add a park neutral switch to this car. tried grounding pin 32 and 34 to gether and separate but nothing. Changed trans type in tune, still noting. it either reads d4 or park in...
  4. Replies
    4
    Views
    1,272

    110817 this seems off to me

    110817

    this seems off to me
  5. Replies
    4
    Views
    1,272

    But in this tune i cant edit where wot closed...

    But in this tune i cant edit where wot closed loop is enabled. and watching on my scan tool the open to closed loop does not change at wot. and at wot my tps is reading 4.89v

    if im reading my...
  6. Replies
    4
    Views
    1,272

    power enrichment

    Where or how does ford do power enrichment in this tune. i have this dial in very nicely execpt during wide open pull i only get about 13.8- 14.1 afr. i have been using a regular scan tool to data...
  7. im still learning, im not sure what scaling...

    im still learning, im not sure what scaling needs done. could you explain
  8. Replies
    3
    Views
    1,245

    ill try that thanks, just got my mpvi2 today.

    ill try that thanks, just got my mpvi2 today.
  9. Can some check my injector data

    Just would like someone to check that i inputted injector data correctly

    I left the high flow rate at 30 only because of some posts i read, is this correct?


    2003 ford mustang gt , 4.6l,...
  10. Replies
    2
    Views
    1,340

    also has an sct ba-2600 maf sensor 90mm

    also has an sct ba-2600 maf sensor 90mm
  11. Replies
    2
    Views
    1,340

    2003 mustang gt tuning help

    been working on the tune and im struggleing. i posted my current tune.
    This is an 03 mustang gt with 4.6l sohc. vortech v1 supercharger installad and a bbk throttle body.
    lu47 ford injectors.
    ...
  12. Replies
    3
    Views
    1,245

    Roush Mustang stage 3

    I pulled this file from a 2019 jackhammer mustang with the stage 3 upgrade.
    File will not open
    just wanted to take a peak at it.
    109924109925
  13. low octane table being used and dont know why

    went to dyno today just to get some numbers and tune was stuck on low octane table. cant figure out what is causing it.

    truck is a 6.0l with 799 heads, ported and polished, comp cam, ls9 valve...
  14. Sorry for the long delay. i ended up having to...

    Sorry for the long delay. i ended up having to replace ecm due to an error witht the prom. would not read ecm. new ecm in. burst knock turned off. it is alot better but at 5000rpm there is still...
  15. sorry here is attachments

    sorry here is attachments
  16. pulling 11.5 deg timing at 5000rpm

    Been trying to figure this out for a while now.
    Truck pulls 11.5 deg timing at 5000rpm at wot.
    any ideas.
    i believe burst knock is turned off and all torque limiting shut off
    2 different logs are...
  17. wide band wasnt hooked up. sorry didnt realize. ...

    wide band wasnt hooked up. sorry didnt realize. truck does run 12.0 +/- .1 throughout the runs
  18. timing problem in 1st and 2nd gear

    My ignition timing is all over the place in 1st gear and 2nd gear. It goes normal in 3rd.
    Cant figure out why.
    the 2 deg low in 3rd gear is due to coolant temp high.

    The tune is the one i pulled...
  19. Replies
    4
    Views
    1,146

    My bad.

    My bad.
  20. Replies
    4
    Views
    1,146

    Ya. It has 2 connectors 1 grey one black.

    Ya. It has 2 connectors 1 grey one black.
  21. Replies
    4
    Views
    1,146

    Which pcm to use

    I am currently swapping a 2008 aluminum 5.3 with 58 tooth reluctor into a 2011 colorado. I have both pcms. The 2008 is an e40 with no DOD. And the other is an e38 from the 5 clyinder colorado. I...
  22. Replies
    3
    Views
    1,394

    Rpm limit not working

    Having trouble getting rev limiter to work. will not cut off. tried using etc, fuel cut and spark. none work. no codes. here is my tune can someone have a look.
  23. Replies
    1
    Views
    1,010

    Real time tunning

    Is there a list of pcms that support real time tunning. I have a gen 3 6.0l dbw in a 2005 silverado. I have being reading any pcms i can get my hands on and none give me the option when switching...
  24. Replies
    6
    Views
    3,372

    thanks for the help. been reading some threads on...

    thanks for the help. been reading some threads on PID adjustments and believe this should correct my idle with some experimentation.
  25. Replies
    6
    Views
    3,372

    have not adjusted the pid controls for o2, cause...

    have not adjusted the pid controls for o2, cause im not sure what that is.
Results 1 to 25 of 29
Page 1 of 2 1 2