Search:

Type: Posts; User: 96 Comp T/A

Search: Search took 0.00 seconds.

  1. Replies
    18
    Views
    10,609

    Hey guys sorry to necropost, but I am struggling...

    Hey guys sorry to necropost, but I am struggling with the same issue. I did check this with an oscilloscope, and I can not get anything out of Pin 41 on the X1 connector of the E78 ECM. I did find...
  2. Thread: LV3 v6

    by 96 Comp T/A
    Replies
    8
    Views
    6,907

    I've got one too. I've got big plans and I have...

    I've got one too. I've got big plans and I have already started to make some parts. Follow my thread over on https://ls1tech.com/forums/conversions-hybrids/1753035-new-gen-v-project.html I...
  3. Replies
    1
    Views
    2,039

    Never mind, a little internet snooping turned up...

    Never mind, a little internet snooping turned up a part # and an application list, it appears the corvette, silverado and the cadillac ATS and CTS all share a common ECU. The part # is 12656993
  4. Replies
    1
    Views
    2,039

    2014 Truck EMC Part #'s

    Can anyone tell me the part # for the 4.3L V6 ECM, and if it matches the 5.3 or 6.2 ECM part #'s? I found an engine for my project, but the computer and harness had already been sold to fix fire...
  5. Replies
    4
    Views
    4,794

    The engine in question is the direct injected 3/4...

    The engine in question is the direct injected 3/4 LT1 new for MY2014 forward Chevy GM Pickups, and has nothing in common with the 08-14 engine (other than displacement). ...
  6. Replies
    4
    Views
    4,794

    That's good news, but I will wait until it shows...

    That's good news, but I will wait until it shows up on the official "supported vehicles list" before I take the plunge. Are you saying you have already tuned one?
  7. Replies
    4
    Views
    4,794

    LV3 Support Forthcoming?

    Any chance the new V6 4.3 LV3 engine will be supported at some point? I would like to use this engine in a buggy swap, but I don't want to risk purchasing one without being able to tune it.
  8. Replies
    39
    Views
    27,943

    To use those cylinder heads you would have to...

    To use those cylinder heads you would have to have the cam lobes swapped. They are backwards compared to Gen3-4.
  9. Replies
    3
    Views
    2,799

    Rolling Idle table

    hey guys, I am using one of the recent betas, and I noticed that there is a new table called rolling idle that is zero'd out. I am having a problem with my car where the idle is extremely high...
  10. I can say with certainty that HPT works using a...

    I can say with certainty that HPT works using a Win7 32 bit VMWare Fusion Image. No problems reading/writing to the PCM, although it does take a couple of seconds for the USB passthrough to...
  11. Replies
    17
    Views
    13,690

    Looking for an update.

    Putting this back up at the top, do any of the betas have this feature yet? My stuff is commanding 11.5 degrees of advance at startup. and takes a couple of attempts to get started. Motor is a low...
  12. Looking for a definitive answer for the GM 2.5 bar sensor

    Hello everyone, I am new to HPTuners. I am planning my Turbo build now for my C6. I have followed the various threads here and on LS1tech like this one...
Results 1 to 12 of 12