Search:

Type: Posts; User: luke111

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Check this website out, it should explain it....

    Check this website out, it should explain it.
    https://www.gribble.org/cycling/air_density.html
  2. Replies
    25
    Views
    875

    Ok post up the files I can have a look at them....

    Ok post up the files I can have a look at them.
    Did you find the injector part numbers and then find accurate injector data for them?
    It will obviously run like crap with the wrong injector data....
  3. Replies
    25
    Views
    875

    Is this your car or is it a customers? Where do...

    Is this your car or is it a customers?
    Where do you live? If you live in Brisbane it might make things easier.
    Does this thing have bigger cams than stock? Most stock barras idle at around...
  4. Replies
    25
    Views
    875

    I have had a look at the files you have posted....

    I have had a look at the files you have posted. There are so many things wrong Im not sure where to start! Whoever has been playing around with this ecu clearly had no idea what they were doing!
    ...
  5. Replies
    1
    Views
    315

    I'd say its Tip In Retard. I had a look at the...

    I'd say its Tip In Retard. I had a look at the log where it goes into pre-ignition spark source. I've never seen that before. Are your ignition timing tables std?
    I've had a play around with the...
  6. Replies
    6
    Views
    833

    File is attached. I managed to get a 10.7@129mph...

    File is attached.
    I managed to get a 10.7@129mph on the weekend out of it so I'm happy.
    I'm not sure how much its holding me back off the line at 75deg instead of 82deg.
    Any help you can give is...
  7. You're better off logging throttle angle in...

    You're better off logging throttle angle in degrees. It should be around 80-82 degs at WOT. You can double check with the ignition on/engine not running.
    I've seen on my car throttle clipped to...
  8. Replies
    17
    Views
    4,077

    The short answer is NO. You really want to setup...

    The short answer is NO.
    You really want to setup a histogram graph with vcm scanner and log your long term fuel trims.
    My first guess is that your injector slopes are not set correctly. You can do...
  9. Replies
    1
    Views
    300

    The short answer is no it doesn't work. I have...

    The short answer is no it doesn't work.
    I have connected the boost sensor to pin C02 and when I log the PID with forscan (No vcm scanner doesn't work), the sensor is stuck on 0.0kpa.
    The LPG or the...
  10. Replies
    3
    Views
    428

    There should be no difference between base model...

    There should be no difference between base model XT and XR6 ecu's as they run the same engine and kW rating.
    I have attached files from a BA & BF Ecus I've owned.
    If you have a specific strategy...
  11. Replies
    3
    Views
    428

    There are a few in the repository. Search under...

    There are a few in the repository. Search under ford australia. You mustn't be looking in the right spot.
  12. Replies
    6
    Views
    833

    If you are referring to Inferred Movement =...

    If you are referring to Inferred Movement = 2800rpm then I have tried changing that higher (6000rpm) and its still there.

    I have set Torque Management; Torque Ratio Clips; Spark Limit; Trans Trunc...
  13. Replies
    6
    Views
    833

    Trans trunc on launch with hi stall

    On my BF turbo setup with BTR 4 speed, I am seeing ETC clipped to 75 deg in 1st gear on launch. I have a 3200 converter.

    I don't seem to get it on the street but If I have drag radials on at...
  14. Replies
    16
    Views
    3,197

    im using a innovate LC2 with a LSU4.9. It has...

    im using a innovate LC2 with a LSU4.9. It has been flawless so far.
  15. Replies
    1
    Views
    300

    Bf lpg ecu on bf turbo

    I've got a ASU-153 BF Dedicated Gas ECU (HACCFY9) that I want to reflash with a turbo strategy. (HACCKJ6)

    I'm hoping that the LPG ecu has the output for the wastegate solenoid and the input for...
  16. Replies
    4
    Views
    620

    Heres a screenshot of what it looks like on...

    Heres a screenshot of what it looks like on cruise control on a flat road. The ecu is doing this opening/closing of the throttle all by itself. This was set on Prop Gain 0.1 (Standard settings)...
  17. Replies
    4
    Views
    620

    I made some progress over the past couple of days...

    I made some progress over the past couple of days by adjusting the Proportional Gain - Electronic Throttle; Feedback control.
    I setup some datalog traces for ETC Desired vs ETC Actual and noticed...
  18. Replies
    29
    Views
    6,067

    Thats handy to know. Thanks!

    Thats handy to know. Thanks!
  19. Replies
    4
    Views
    620

    Cruise Control Surging

    Hope someone can please help me out?
    I've got an issue with my car that I've never been able to sort out - with cruise control surging especially going up or down hills. Flat road its not too bad.
    ...
  20. Replies
    7
    Views
    553

    OK I've had a look at your tune. I don't know...

    OK I've had a look at your tune. I don't know where to start. Looks like its still mostly NA settings. It all looks really bad to be honest.
    This is my advice (take it with a grain of salt but it...
  21. Replies
    7
    Views
    553

    I've never heard of the FG map sensor swap but...

    I've never heard of the FG map sensor swap but that's handy to know!
    I cut the connector and resoldered the wires when I went from BA NA to BA turbo.
    I see you are running strategy HAAN9AW - and...
  22. Replies
    7
    Views
    553

    It should be there under Airflow, General. Post...

    It should be there under Airflow, General.
    Post up a copy of the file your working with. I've done a few NA to turbo ecu conversions BA & BF. I should be able to help you get it going. PM me if you...
  23. Make sure you are also logging ambient air temp...

    Make sure you are also logging ambient air temp in lh column.

    I can see that you are missing the unit for AAT.
    Looking at the expression for that I can see an error.
    You have (50008.24) instead...
  24. Can you be more specific of whats happening? Is...

    Can you be more specific of whats happening? Is it the chart on the bottom right not showing the trace? or can you share a screenshot? I forgot to add that you need to be logging these channels in...
  25. I have attached some files to help.

    I have attached some files to help.
Results 1 to 25 of 57
Page 1 of 3 1 2 3