Search:

Type: Posts; User: Mbrowning

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. No harm at all.

    No harm at all.
  2. Try going under fuel/cutoff defco/, and disable...

    Try going under fuel/cutoff defco/, and disable ETC control method.
  3. Thread: Start/Stop

    by Mbrowning
    Replies
    16
    Views
    9,529

    If it has a battery sensor, unplug it and it...

    If it has a battery sensor, unplug it and it start/stop will be disabled. Go in diag tab and set trouble code to "no mil".
  4. 109472 You need to max out your decreasing rate...

    109472
    You need to max out your decreasing rate limits. I modified your file and attempted to upload. Hope this helps.
  5. Replies
    11
    Views
    7,120

    I disabled it on a 2017 Cadillac XT-5 by doing...

    I disabled it on a 2017 Cadillac XT-5 by doing the following.

    I unplugged the battery sensor which causes the ecm to disable auto stop. The only thing left to do is pull the code, and go in your...
  6. Replies
    3
    Views
    1,391

    If you can upload the file, it should be easy to...

    If you can upload the file, it should be easy to spot. If you are running a gen v OS, then the problem is most likely the DD tables.
  7. It bypasses the vehicle communication interface,...

    It bypasses the vehicle communication interface, which is required for their scan equipment to check your vehicle and update as needed. If you don't take it out, they most likely will (and charge you...
  8. Replies
    9
    Views
    3,376

    You can get in trouble quick with those tables....

    You can get in trouble quick with those tables. That's why they warn you to change them at your own risk. If you increase the ENTIRE table by 5 or 10 percent. It makes the entire vehicle react...
  9. Replies
    9
    Views
    3,376

    On the driver demand tables, highlight the WHOLE...

    On the driver demand tables, highlight the WHOLE TABLE and multiply by 1.1. Tables A and C are the ones to modify.
  10. Replies
    9
    Views
    3,376

    I touched up your file to give you some stuff to...

    I touched up your file to give you some stuff to look at. I learn a lot looking at changes and researching the definitions and noting changes. The changes I made are the same ones I use in my 2017...
  11. Replies
    9
    Views
    3,376

    I recommend going to discrete shift mode and...

    I recommend going to discrete shift mode and disable the 2-3. 1 is enabled, 0 is disabled. Next, to firm up the shifts, go the the shift timing tab, then torque adder. These are the tables that add...
  12. Good point ZincGT. I had hoped to find a lost...

    Good point ZincGT. I had hoped to find a lost Ford tuner looking for LS help. This was all a total waste of time really. I am going to close this on a good note. If there is anyone stuck on a GT350...
  13. Works for me. I was looking for a Ford tuner that...

    Works for me. I was looking for a Ford tuner that needed a LS tuner. Guess I should have rephrased my question. However, that does not excuse your condescending attitude. Move along please because as...
  14. In the future, save your opinion for someone that...

    In the future, save your opinion for someone that wants it, mbray01
  15. Replies
    15
    Views
    3,063

    Just an update. I solved my problem with a custom...

    Just an update. I solved my problem with a custom table that works really well with driver demand. Case closed. Thanks everyone.
  16. My main concern was the throttle body. The...

    My main concern was the throttle body. The customer had a 2016 GT 5.0 with a 5.2 voodoo intake ant gt350 throttle body. The math is WAY DIFFERENT for the two. After about six hours of math and...
  17. OK...i'll start with VCT

    OK...i'll start with VCT
  18. I'm looking for a Ford guy with LS problems.

    I'm looking for some help with a 2016 mustang 5.0 in trade for some help with LS. Any takers?
  19. Replies
    15
    Views
    3,063

    2016 Mustang GT tuning questions

    Hello everyone. I have a 2016 Mustang GT with a CAI, 5.2 voodoo intake, and gt 350 throttle body. Not my car personally but one that was offered to me as a learning tool. I've had good success with...
  20. Replies
    11
    Views
    5,884

    That's awesome and all, but you can still tune a...

    That's awesome and all, but you can still tune a truck ahem, "correctly" and still make the driver demand table more responsive. The tables mentioned affect more than just the engine and transmission.
  21. Replies
    11
    Views
    5,884

    Any or all four. Modify the ones you want to...

    Any or all four. Modify the ones you want to respond more aggressively.
  22. I haven't logged to know for sure. Actually, it's...

    I haven't logged to know for sure. Actually, it's most likely redundant to disable rate limits if you max the tables out. If I remember, at first there was not a disable option. I think it was added...
  23. Replies
    11
    Views
    5,884

    Take table "A" and table "C" and modify this way....

    Take table "A" and table "C" and modify this way. Highlight the entire table and multiply by 1.05. This adds 5 percent to the entire table. The first instinct is to look at the bottom half of the...
  24. 95990 If you open your file in the beta...

    95990

    If you open your file in the beta version, you will see immediate and predicted torque increase. Make sure they are maxed out. Disable torque request rate limit. This was some code that GM...
  25. Replies
    55
    Views
    142,651

    I'm messing with 4.5 beta. Some direction would...

    I'm messing with 4.5 beta. Some direction would be nice. These gen v's are tough. So many pid's need to be polled.
Results 1 to 25 of 75
Page 1 of 3 1 2 3