Search:

Type: Posts; User: anniversaryss

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds; generated 10 minute(s) ago.

  1. Replies
    25
    Views
    2,129

    Although I've tested mine in varying conditions...

    Although I've tested mine in varying conditions in open loop my AFR seems to stay pretty good between 93 and and flex blends and flex sensor
  2. Replies
    17
    Views
    1,578

    I used an unused set of wires. In my case the EGR...

    I used an unused set of wires. In my case the EGR wire. I connected the 12v and the second wire I swapped at the pcm connector to blue connector pin 56 for the signal. Then ran a ground.
  3. Replies
    17
    Views
    1,578

    Got a little E in the tank. A low percentage...

    Got a little E in the tank. A low percentage since I had fuel in there anyways. I'm understanding how this works.
    The AFR was on point which I'm happy about.
    HPT is missing the spark blend factor...
  4. Replies
    17
    Views
    1,578

    Alright so logging Eq ratio I changed the units...

    Alright so logging Eq ratio I changed the units to AFR. And it seems to be going correctly.
    Thanks guys I really appreciate it. Always learn something new .
  5. Replies
    17
    Views
    1,578

    Kinda common sense I suppose but just put in some...

    Kinda common sense I suppose but just put in some flex , unknown content, into my 5/8 full tank and everything seems to work. Obviously have to use LAMBDA now lol. The percent error seems in line...
  6. Replies
    17
    Views
    1,578

    You can use the same OS from an avalanche if you...

    You can use the same OS from an avalanche if you need an 80e segment
  7. Replies
    17
    Views
    1,578

    Im using the 02 Tahoe OS iirc

    Im using the 02 Tahoe OS iirc
  8. Replies
    17
    Views
    1,578

    Flex/E85 tuning with 0411

    Finished up tuning on pump 93 getting ready to move to flex/e85. Have some basic questions. I understand the 0411 isn't amazing at it but it's what I got.

    Let's say my Error on 93/E10 is roughly...
  9. Replies
    7
    Views
    709

    I agree. I'm working my way in there. I def have...

    I agree. I'm working my way in there. I def have to do some plug reads.
    I think we talked in another post I made about knock sensors and I planned on swapping to the ks7 sensor to test. Still seems...
  10. Replies
    7
    Views
    709

    Absolutely!! I had a feeling you'd say something...

    Absolutely!! I had a feeling you'd say something similar to that. The knock detection coming from the pcm tends to be random and sometimes I get it, sometimes I don't. As I said i could go for...
  11. Replies
    7
    Views
    709

    I just ran 20 degrees up top and showed 1 - 1.6...

    I just ran 20 degrees up top and showed 1 - 1.6 degrees of knock but I could probably go for another hit and not show any.

    Right now my WOT fueling is set to 11.48 but the 9% ethanol reading...
  12. Replies
    7
    Views
    709

    LT1 24x H/C/I Procharged

    KInda just seeing how things are going, looking for advice and critiques.

    Car is a gen 2 LT1 24x of course. Pro charger 14.5psi. TFS 180 ported heads, 223/235 114 cam, mostly forged but wasnt...
  13. Replies
    6
    Views
    738

    Segment swap the manual trans/diagnostics from...

    Segment swap the manual trans/diagnostics from the same OS and try again.
    Sometimes just choosing manual from auto just doesn't work.
  14. Yeah I'll get back on the dyno sooner or later...

    Yeah I'll get back on the dyno sooner or later I'm enjoying street tuning for now. I prob wont up the timing anymore until I get on the dyno
  15. Thank you Ben. Yes I'm working in it slowly for...

    Thank you Ben. Yes I'm working in it slowly for now. As you said I feel like I'm pretty close to being set with timing until I run E85.

    I'll keep updating as I go. Once a week is slow moving lol
  16. I'm up to 18 degrees and I'm at 14.5-15 psi. A...

    I'm up to 18 degrees and I'm at 14.5-15 psi. A little more than expected.
    I havent seen any real knock event yet. Tuning on 93 at the moment and e85 sooner or later.

    Also using the KS7 or...
  17. I installed the KS7 today. Going to get some seat...

    I installed the KS7 today. Going to get some seat time in soon
  18. I'm assuming its "fuel pressure delay" it says...

    I'm assuming its "fuel pressure delay" it says "delay after key on, before pulse is delivered to allow pump to build pressure."
  19. Thank you I'll check that out. Much appreciated

    Thank you I'll check that out. Much appreciated
  20. I don't have a check valve for my pumps so I...

    I don't have a check valve for my pumps so I typically prime once or twice and it starts right up.
  21. Replies
    5
    Views
    1,070

    GM does some crazy stuff. Iirc the truck...

    GM does some crazy stuff. Iirc the truck settings will put your dwell in the low to mid 3ms range. It should be fine. I would personally swapped over all settings
  22. Replies
    5
    Views
    1,070

    I would use the dwell settings form whatever...

    I would use the dwell settings form whatever vehicle uses the d585 coils (usually the trucks).

    If you look at the dwell + multipler on fbody pcms they are well above 5ms and then some. That's my...
  23. Looks like he has SEP1000 which I'm assuming are...

    Looks like he has SEP1000 which I'm assuming are the injectors. Other than SEP having a bad rep for bad injectors you should lower your min fule milligrams
  24. Yeah according to GM parts direct and advance...

    Yeah according to GM parts direct and advance auto those are the correct part numbers for the 2002 Express 5.7.

    The ks7 is like 30 bucks the ac delco is 60
  25. The 5.0 l30 has a different part number than the...

    The 5.0 l30 has a different part number than the 5.7 l31
Results 1 to 25 of 496
Page 1 of 20 1 2 3 4