Search:

Type: Posts; User: v8miata

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    I actually don?t know, I have an extra set of...

    I actually don?t know, I have an extra set of o2?s I?ll swap out. I will look into info on the injectors. I purchased them as remanufactured and really didn?t get much info on them. I?ll contact...
  2. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    I am using the hot parts from CX racing driver...

    I am using the hot parts from CX racing driver side crosses over to passenger side into turbo then downpipe back to muffler I don't hear any exhaust leaks but I will check closely later this...
  3. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    no vaccum leaks that I can find. I even went to...

    no vaccum leaks that I can find. I even went to an aresol after checking all of my vacuum connections I added fuel and it just added, didn't change the drop. should I try an open loop? I did...
  4. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    ok I tried both and its the same, any other...

    ok I tried both and its the same, any other ideas?901509015190152
  5. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    ok, I changed it back to mil on first and made...

    ok, I changed it back to mil on first and made sure it saved
    then I just ran it and still thre same issue9014190142
  6. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    I don?t know how the mass air codes keep...

    I don?t know how the mass air codes keep reverting. I wrote it again just now
  7. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    The injectors are 60lb at 58

    The injectors are 60lb at 58
  8. Thread: LTFT question

    by v8miata
    Replies
    12
    Views
    2,554

    LTFT question

    Can someone look at this log and tell me if the ltft is the cause of my air/fuel going completely lean when i let off the throttle and why? I want to understand.9013390134
  9. Replies
    8
    Views
    2,130

    Just for the extra info, I had to use the LM...

    Just for the extra info, I had to use the LM Programmer to change the output of the output #2 to match the output 1#. #1 is used for the gauge leaving #2 which is set up different. Very easy change...
  10. Replies
    0
    Views
    636

    charting boost pressure

    does anyone know how to set up this chart to show boost pressure instead of absolute. I don't have a barometric pressure sensor, can I add one somehow?
  11. Replies
    8
    Views
    2,130

    Ok, so I?ve found that there is a problem with...

    Ok, so I?ve found that there is a problem with the LC-2 output. I gentleman named Corey checked and said everything was set up correctly on my chart side so I?ve got to figure out what?s going on on...
  12. I have an LC-2 and I need help. I have connected...

    I have an LC-2 and I need help. I have connected as all info I found said and in my chart and channel it shows 7.7- 10.8 while my gauge reads 14.2. I don't know how to get this to chart correctly. ...
  13. Replies
    8
    Views
    2,130

    That?s exactly how I set it up. In my channel...

    That?s exactly how I set it up. In my channel it shows 7.7 and on the chart it shows the same while my air/fuel gauge is reading 15
  14. Replies
    8
    Views
    2,130

    Thank you so much, I?ll try that this afternoon.

    Thank you so much, I?ll try that this afternoon.
  15. Replies
    9
    Views
    4,658

    I just finished the Banish book Engine management...

    I just finished the Banish book Engine management / advanced tuning. It was very well written and helped me with a great deal of understanding.
  16. Replies
    8
    Views
    2,130

    89968

    89968
  17. Replies
    8
    Views
    2,130

    LC-2 will not chart correctly

    I am pulling my hair out here trying to get this to chart correctly my air fuel is at 14.5 -14.9 at idle under boost its 11.3 - 11.5 PLEASE HELP ME89932
  18. Replies
    20
    Views
    4,331

    Changes

    8993089931

    Please check this out, ive got a little 150 rpm idle surge I cant seem to get rid of. and I cant seem to get my LC-2 to read correctly gauge is reading correctly but it will not chart...
  19. Replies
    20
    Views
    4,331

    the injectors are rated at 43 and my pressure...

    the injectors are rated at 43 and my pressure stays around 50 I did get the MAF fail set at 0 and the 3dtc are set to mil on first error do the ses check boxes need to be checked?
  20. Replies
    20
    Views
    4,331

    Does anyone know how to calibrate the IAS. Are...

    Does anyone know how to calibrate the IAS. Are there tables or charts top go off of?

    I am struggling to get the log to show pretty much anything. I changed the map channel but it is still...
  21. Replies
    20
    Views
    4,331

    I'm sorry I looked back and from my phone I...

    I'm sorry I looked back and from my phone I didn't see this. This is incredibly helpful ill start into making changes and reading inon it. thank you so much.
  22. Replies
    20
    Views
    4,331

    [QUOTE=5FDP;569065]Do more of the stuff I suggest...

    [QUOTE=5FDP;569065]Do more of the stuff I suggest in post 13.

    Some things still need to be squared away so this tune is working right with the parts you are using. Like injector scaling and your...
  23. Replies
    20
    Views
    4,331

    here is a log after and the tune I tried89257

    here is a log after and the tune I tried89257
  24. Replies
    20
    Views
    4,331

    ok I've made the suggested changes and its...

    ok I've made the suggested changes and its running good do I need theses enable checkboxes checked? and I have it dropping into low 11 under boost
  25. Replies
    20
    Views
    4,331

    89254

    89254
Results 1 to 25 of 31
Page 1 of 2 1 2