Search:

Type: Posts; User: CFGBR95

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. The channels are for my EU ST so you may not have...

    The channels are for my EU ST so you may not have all the same PIDs.

    We want to see torque source for driver demand. Will look at your log either tonight or tomorrow if I get time. You happy with...
  2. Try this, I've blended some tables from the ST...

    Try this, I've blended some tables from the ST too allow for more load and torque.

    I've also attached the channel config for when I tune my ecoboost
  3. Will look later but there definitely is one on...

    Will look later but there definitely is one on there.
  4. Look on the tune repository

    Look on the tune repository
  5. Replies
    7
    Views
    410

    I'm using AD firmware. My email is...

    I'm using AD firmware.

    My email is [email protected]
  6. Replies
    7
    Views
    410

    It depends on what firmware your car runs to...

    It depends on what firmware your car runs to whether all the required tables exposed.

    I have my STG3 ST180 file which will maintain around 1.7bar until the redline, however without seeing what...
  7. Replies
    7
    Views
    410

    Can you post your file?

    Can you post your file?
  8. Replies
    7
    Views
    410

    If you're running the stock turbo, you'll be...

    If you're running the stock turbo, you'll be pushing it out of its efficiency range by trying to request 270kpa at the top. It tails off as it can't sustain the boost.
  9. Replies
    9
    Views
    2,056

    VCM editor doesn't have the offset for the...

    VCM editor doesn't have the offset for the duration table correct, the duration is actually 1.5 seconds for Baja and 3.0 seconds stock, checked via a winols definition.
  10. 2018+ MK8 Fiesta 1.0 Ecoboost MED17.0.7 384k

    Hi all,

    I see HP Tuners claim that they support this car however when I go to take a read, it say 'Not Authorised'. Has anyone successfully used HP to tune one of these?

    I contacted support...
  11. Do you have a read of your stg1 file?

    Do you have a read of your stg1 file?
  12. Replies
    2
    Views
    734

    Read the ECM with no input, why?

    Read the ECM with no input, why?
  13. Replies
    6
    Views
    968

    See how this logs, put the ignition timing back...

    See how this logs, put the ignition timing back to stock as your inferred RON rating is 93 which isnt great, what grade petrol are you using? Ideally you want to be using 93 octane/98RON else it'll...
  14. Replies
    6
    Views
    968

    Try this, I've turned on all the limiters you...

    Try this, I've turned on all the limiters you turned off as there isnt a need to turn them off from my experience, including any DTC trigger changes. I've also copied over your transmission...
  15. Replies
    1
    Views
    396

    Try this as a base and log it for knock etc140545

    Try this as a base and log it for knock etc140545
  16. Thread: Burble logic

    by CFGBR95
    Replies
    45
    Views
    10,164

    Try this

    Try this
  17. Your car uses the same ecu structure as the Focus...

    Your car uses the same ecu structure as the Focus RS, so it will have dedicated Burble control logic within it. HP Tuners has already defined them all for the RS, so you should drop them a ticket and...
  18. Replies
    2
    Views
    576

    Just change the row values to whatever you desire.

    Just change the row values to whatever you desire.
  19. Replies
    9
    Views
    2,056

    All's it does is crack the throttle open when you...

    All's it does is crack the throttle open when you let off to let the desired airflow be met, doesn't really make much difference to be honest.
  20. Replies
    41
    Views
    5,973

    Did you have any luck with this? Find myself in a...

    Did you have any luck with this? Find myself in a similar situation now with a MK8 1.0 Fiesta. Won't read the car as apparently it's not authorised.
  21. No it isn't.

    No it isn't.
  22. The full read you did via Autotuner may be...

    The full read you did via Autotuner may be garbage as COBBs firmware is usually heavily encrypted. You'll never be able to get a read using your MPVI3 without flashing a full stock file. COBBs custom...
  23. Replies
    7
    Views
    1,043

    Need a specific BETA version of Forscan to do it.

    Need a specific BETA version of Forscan to do it.
  24. Replies
    7
    Views
    1,043

    If it's been flashed using a COBB, it will need a...

    If it's been flashed using a COBB, it will need a full factory Ford flash before you can even start read/writing the card as the ECU will contain COBB custom code in the firmware hence why you can't...
  25. Replies
    15
    Views
    2,505

    Any update on this?

    Any update on this?
Results 1 to 25 of 128
Page 1 of 6 1 2 3 4