Search:

Type: Posts; User: sprinto7

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. I have some experience with Trifecta, overall I'd...

    I have some experience with Trifecta, overall I'd say it was a very good experience. Any problems we had were all self induced like not knowing what MAP sensor I was actually using, and things like...
  2. Replies
    7
    Views
    2,852

    Clutch position learn procedure

    There must be a write up of this procedure somewhere.
    In my 2015 Trax RWD standalone swap, using the Trax E78 ECM with tune based off a Sonic Manual transmission ECM tune "write entire" I can find a...
  3. Replies
    7
    Views
    314

    Sometimes it takes a while to get a response. Is...

    Sometimes it takes a while to get a response.
    Is yours the iron block, or the aluminum block. The aluminum block is direct injection here in the USA.
  4. I assume by the term Scan Tool you mean HPT VCM...

    I assume by the term Scan Tool you mean HPT VCM Scanner. Just where and how do we get to "Clutch Pedal Position Sensor Learn"?
  5. Me Too. I got it to work once 6 moths ago, but I...

    Me Too. I got it to work once 6 moths ago, but I can't get it tp work now..
  6. Replies
    7
    Views
    2,852

    This is KIND of Funny. Here it is 6 months later....

    This is KIND of Funny. Here it is 6 months later. I changed the size of the master cylinder. Now I can't remember how to set it. I'll go try it again.

    I must be losing my mind, I can NOT get it to...
  7. Replies
    2
    Views
    133

    I don't know much about 4L80E but too much about...

    I don't know much about 4L80E but too much about VSS, and DD. Where are you getting signal from transmission? Is there an installed on the transmission VSS? Which DD box do you have?
  8. Replies
    4
    Views
    385

    Yess, I have Gen I pro set with External...

    Yess, I have Gen I pro set with External attachment. I'm already logging an external fuel pressure guage/sensor. OOOPS, I was so excited I answered the wrong question.
    I'm looking for how to...
  9. Yess, I have Gen I pro set with External...

    Yess, I have Gen I pro set with External attachment. I'm already logging an external fuel pressure guage/sensor.
  10. Replies
    4
    Views
    385

    I'm beginning to think no body logs turbo speed...

    I'm beginning to think no body logs turbo speed sensors.

    :-(
  11. Replies
    4
    Views
    385

    Can someone explain how a "transform" works? How...

    Can someone explain how a "transform" works? How do I build my own? I need to change a pulse to a Tachometer type gauge.
    Thanks
    Sprinto7
  12. Replies
    4
    Views
    385

    Turbo speed sensor logging

    I need help hooking up the 5V pulse signal from a Garrett Turbo speed sensor. I have the 5V signal attached to the analog input 2 on my first gen HPT Pro box. I can log the 5V on the MPVI-2 Channel,...
  13. Replies
    1
    Views
    215

    I know this was a long time ago, but, I would try...

    I know this was a long time ago, but, I would try mounting an ABS wheel speed sensor ring on the trans to rear end couple then putting a 5V sensor on the out side edge of the wheel. hook the out put...
  14. What PCM are you using? E78? My 2015 Trax PCM...

    What PCM are you using? E78? My 2015 Trax PCM (E78) has a brake position sensor input. I installed a brake pos sensor on my standalone swap. The PCM sees the sensor when the pedal is pushed. I have...
  15. Replies
    8
    Views
    725

    The rev limit I 'm speaking of is in a hidden...

    The rev limit I
    'm speaking of is in a hidden file.
  16. Replies
    7
    Views
    2,852

    OK, I got my switch to "learn" and operate...

    OK, I got my switch to "learn" and operate correctly. My switch is attached to an E78, but the setup is with a RWD Trax 1.4 turbo engine and an inline T5 transmission so NOTHING is standard. I broke...
  17. Replies
    7
    Views
    2,852

    OK, I got the Clutch pedal learn button to...

    OK, I got the Clutch pedal learn button to activate, but I haven't got the switch to learn correctly. I've never seen one of these "switches" in the native state. Mine is from a 2015 Chevy Cruze, and...
  18. Replies
    7
    Views
    2,852

    There must not be a large number of us that try...

    There must not be a large number of us that try to hook the clutch position switch up in a swap. I have the switch in place, but I can't find the "CLUTCH LEARN" button. It may be in the VCM Control...
  19. Replies
    2
    Views
    253

    Did you get an answer to this?

    Did you get an answer to this?
  20. Replies
    2
    Views
    311

    What do you mean by "light" flywheel? I just have...

    What do you mean by "light" flywheel? I just have a flex plate to engage starter.
  21. Replies
    8
    Views
    725

    Do you mean "Case Learn"? I don't think that is...

    Do you mean "Case Learn"?
    I don't think that is it, but I could be wrong.
    I think it's hidden in a table that we can't see.
    HPT would have to unlock it.
  22. Replies
    8
    Views
    725

    If that is adjustable, how do we get at it?

    If that is adjustable, how do we get at it?
  23. Replies
    8
    Views
    725

    GM 1.4 E78 PCM 4300 Rev Limit

    E78 PCM. Vehicle not moving, NO VSS. WOT produces 4300 RPM Rev limit. What table is 4300 in? How do you change the 4300 limit?
    This particular stand alone set up is 2015 Trax manual in...
  24. Replies
    21
    Views
    3,565

    The E78A is used in the Direct Injection "new...

    The E78A is used in the Direct Injection "new version" 1.4 Turbo with aluminum block.
  25. Replies
    13
    Views
    2,465

    I have been give an explanation for this...

    I have been give an explanation for this situation by someone I consider an expert with the 1.4 turbo engine.
    This vehicle is an Autocross only vehicle, so it is only run in 1st and 2nd gear. He...
Results 1 to 25 of 192
Page 1 of 8 1 2 3 4