Search:

Type: Posts; User: dsltech83

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    517

    HPT can only change pcm. Advancetrac is in the...

    HPT can only change pcm. Advancetrac is in the ABS module.
  2. Replies
    2
    Views
    205

    Those codes mean the cam timing is mechanically...

    Those codes mean the cam timing is mechanically off
  3. Replies
    6
    Views
    805

    Yes I would open a support ticket. Ficm voltage...

    Yes I would open a support ticket. Ficm voltage is supported on some calibrations.
  4. Ok. I may have to send a support ticket, my...

    Ok. I may have to send a support ticket, my button to repoll for channels doesn't light up.
  5. Replies
    0
    Views
    245

    5R110 tcc hot lock

    Can anyone tell me what the 22824 - Trans TCC Hot Lock Min Speed Ratio: Speed Ratio must be above this value for the TCC to lock in Hot Lockup mode , anyone have an explanation for it? Not surewhat...
  6. Do all of the channels work on your truck? My 05...

    Do all of the channels work on your truck?
    My 05 excursion all of them won't function.
  7. FPDM is not ment to be used with a return style...

    FPDM is not ment to be used with a return style fuel system. It can't control pressure so it pulls power.
  8. What year crown vic?

    What year crown vic?
  9. Replies
    1
    Views
    385

    I'd email support.

    I'd email support.
  10. Replies
    5
    Views
    560

    Thank you!

    Thank you!
  11. Replies
    5
    Views
    560

    Really just looking for advice on where to stop...

    Really just looking for advice on where to stop with boost, probably won't even mess with timing. Going to play with shift scheduling and tcc a little too.
  12. Replies
    5
    Views
    560

    Going to make a safe tow tune.

    Going to make a safe tow tune.
  13. Replies
    5
    Views
    560

    2013 F150 tow tune

    Anybody have any experience with this? Towing a 5500 lb travel trailer, going to write a tune around that. Low elevation (around 500 ft where I live), stock truck except for an intake that was on it...
  14. Jim Ferraro @ Ferraro speed would be the man to...

    Jim Ferraro @ Ferraro speed would be the man to talk to about that.
  15. For what its worth, I have read and wrote my 05...

    For what its worth, I have read and wrote my 05 Ex 6.0 with 3.6 no problem. I'll try with 3.7 when I get the heads back on it.
  16. Thread: fan control

    by dsltech83
    Replies
    6
    Views
    455

    So set the desired ECT to 200* then. That way...

    So set the desired ECT to 200* then. That way the fans won't mess with the thermostat opening. The ECT table looks at ECT and ambient temperature to set fan speed. The AC table controls fan speed...
  17. Thread: fan control

    by dsltech83
    Replies
    6
    Views
    455

    There is no High speed fan and low speed fan. ...

    There is no High speed fan and low speed fan. The tables are for the percentage of fan speed. Fans are pulse width modulated not a set speed.
  18. Thread: fan control

    by dsltech83
    Replies
    6
    Views
    455

    No in fan speed vs. ECT table, table 44002 you...

    No in fan speed vs. ECT table, table 44002 you set fan speed percentage vs. ECT. table onlygoes down to 200 degrees, if you want fan control below that you will have to rescale the column axis on...
  19. Thread: fan control

    by dsltech83
    Replies
    6
    Views
    455

    Go to System>Fans>Desired ECT set 10* above...

    Go to System>Fans>Desired ECT set 10* above Thermostat.
    In Fan speed vs. ECT you will have to re scale the axis to ge the fans on that low. 160 is awful low for todays engines. Dont normally make...
  20. Thread: MAF Delete

    by dsltech83
    Replies
    4
    Views
    644

    Thanks Eric. I thought that was true. They told...

    Thanks Eric. I thought that was true. They told us that in Ford school when I was a dealership tech, but wanted to make sure before I just made it go away.
  21. Thread: MAF Delete

    by dsltech83
    Replies
    4
    Views
    644

    MAF Delete

    Is it possible to delete the MAF on a 6.0? Not used for fueling correct? Just EGR flow determination?
  22. Replies
    1
    Views
    751

    Try the GM gen 3 forum. Might get more traffic...

    Try the GM gen 3 forum. Might get more traffic that way.
  23. Replies
    3
    Views
    1,183

    Send a help ticket to support. Edelbrock may use...

    Send a help ticket to support. Edelbrock may use some kind of special os.
  24. Replies
    1
    Views
    697

    Those early 11's had shift solenoid issues when I...

    Those early 11's had shift solenoid issues when I was a dealer tech.
  25. Replies
    1
    Views
    518

    The factory ford scanner (IDS) doesn't have any...

    The factory ford scanner (IDS) doesn't have any balance rates, HPT probably not going to show any. IDS does have a power balance screen to show which cylinders are not contributing though.
Results 1 to 25 of 31
Page 1 of 2 1 2